Cylinder Head Valves
Show/hide table
| |
| Illustration 1 | g06096934 |
|
Typical example | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 1 | 4 | 316-5976 Spring | Length under test force is Test force is Free length after test is |
| 2 | 4 | 316-5977 Spring | Length under test force is Test force is Free length after test is |
| 3 | 2 | 316-5980 Valve Stem Seal | Install the valve stem seal to the inlet valves. |
| 4 | 2 | 316-5981 Washer | Install the washer to the exhaust valves. |
| 5 | 2 | 197-6995 Valve Guide | Bore of the exhaust valve guide after installation is |
| A | - | - | Height from the top of the cylinder head to the top of the valve guides is |
| 6 | 2 | 133-9306 Valve Guide | Bore of the inlet valve guide after installation is |
| 7 | 2 | 468-8825 Exhaust Valve | Before assembly, coat the exhaust valve stems with clean engine oil.
Stem diameter (B) is Valve diameter (D) is Face angle is 45.60 ± 0.25 degrees. |
| 8 | 2 | 468-8824 Inlet Valve | Before assembly, coat the inlet valve stems with clean engine oil.
Stem diameter (C) is Valve diameter (E) is Face angle is 19.40 ± 0.25 degrees. |
| 9 | 2 | 130-2608 Valve Seat Insert | Diameter of exhaust valve seat insert is Bore in the cylinder head is Face angle is 45.00 ± 0.25 degrees. |
| 10 | 2 | 130-2607 Valve Seat Insert | Diameter of inlet valve seat insert is Bore in the cylinder head is Face angle is 20.00 ± 0.25 degrees. |
Caterpillar Information System:
3516B Generator Set with Dynamic Gas Blending Cylinder Head
320 D3 Hydraulic Excavators Engine Disassembly and Assembly Cylinder Liner - Remove and Install
XQP1100 Generator Set Generator Bearing - Lubricate
New Engine Software is Now Used for Certain C175 Generator Set Engines {1920} New Engine Software is Now Used for Certain C175 Generator Set Engines {1920}
New Engine Software is Now Used for Certain C175 50Hz Generator Set Engines {1920} New Engine Software is Now Used for Certain C175 50Hz Generator Set Engines {1920}
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Product Identification
XQP1100 Generator Set Parallel Operation
Cat® Detect Object Detection Hardware Generation 4 for Small Off Highway Trucks, Motor Graders, Large Wheel Loaders, Large Wheel Dozers and Articulated Trucks Declaration of Conformity
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Belt Tensioner - Remove and Install
G3516 TA Engine Restriction of Air Inlet and Exhaust
794 AC Off-Highway Truck Machine Systems Wheel and Brake - Remove and Install
XQP1100 Generator Set Generator Winding - Test
3516B Generator Set with Dynamic Gas Blending Piston and Rings
3516B Generator Set with Dynamic Gas Blending Air Starting Motor Pressure Regulating Valve
PM820, PM822, and PM825 Cold Planer Machine Systems Piston Pump (Hydraulic Fan) - Remove and Install
3516B Generator Set with Dynamic Gas Blending Air Inlet and Exhaust Lines
336, 336 GC and 340 Excavator Systems Pump Control (Output Flow) - Adjust
3516B Generator Set with Dynamic Gas Blending Air Inlet and Exhaust Lines
3516B Generator Set with Dynamic Gas Blending Engine Oil Lines
New E-Stop Contact Blocks Are Now Used on Certain Cat® Engines {1408, 7418} New E-Stop Contact Blocks Are Now Used on Certain Cat® Engines {1408, 7418}
3516B Generator Set with Dynamic Gas Blending Cylinder Block
XQP1100 Generator Set Fuel System Primary Filter (Water Separator) Element - Replace - If equipped
XQP1100 Generator Set Fuel System Primary Filter/Water Separator - Drain - If equipped
XQP1100 Generator Set Fuel System Primary Filter/Water Separator - Drain - If Equipped