Recoil Spring - Disassemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 4C-9540 | 反冲弹簧台架 | 1 |
B | 146-2457 | 液压电源总成 | 1 |
223-3506 | 液压油缸和管路总成 | 1 | |
C | 8S-9971 | 齿座 | 1 |
D | 4C-4467 | 65 mm 套筒 | 1 |
开始:
- 拆下前引导轮和缓冲弹簧组件。
- 拆解反冲弹簧组件之前,请确保工具 (A) 位于水平表面。
- 拆解之前,请彻底清洁反冲弹簧组件的外表面。
Show/hide table
图 1 g00483426 - 如图所示,将工具 (C) 安装到工具 (B) 上。
Show/hide table
图 2 g00494710 Show/hide table图 3 g00483437 注: 两个可调的支承 (1) 、反应板 (2) 和活动板 (3) 均为工具 (A) 的组成部分。
- 调整反作用板 (2) 和活动板 (3) 之间的间距。 间距应该与缓冲弹簧组件的长度(自由长度)大约相同。 此外,请确保两个可调的支承 (1) 安置在反作用板与活动板之间,如图所示。 放平两个支承。
注: 反冲弹簧组件可从末端安装到工具 (A) 中。 在这种情况下,必须拆下反作用板 (2)。 反冲弹簧组件在两个可调的支承 (1) 上就位后,重新安装反应板。
Show/hide table注意 请勿从反冲弹簧组件拆下起重机,直到装置水平、居中并且锁定到指定的工具中为止。
- 反冲弹簧组件的组合重量约为
116 kg (255 lb) 。 - 将适当的起吊设备紧固到反冲弹簧组件上。 将反冲弹簧组件放在工具 (A) 中两个可调支承 (1) 上的相应位置。
- 调整两个可调支架,以便将反冲弹簧组件的中心线对准工具 (A) 的中心线。
Show/hide table
图 4 g00498760 已从反冲弹簧组件上拆下起重装置,以便更好地展示油位表 (4)。 - 将油位表 (4) 置于反冲弹簧组件上。
Show/hide table
图 5 g00498781 - 重新定位缓冲弹簧组件,直至缓冲弹簧组件处于水平位置。 重新定位缓冲弹簧组件,直至固定杆和螺母 (6) 位于反作用板 (2) 上的孔的中心。
- 通过将可调的支承 (1) 移动到更高或更低位置,使反冲弹簧组件处于水平位置。 反冲弹簧组件处于水平居中位置后,将两个销 (5) 安装到反应板 (2) 的背面,如图所示。
- 操作工具 (B) 使其能够将缓冲弹簧组件固定在反作用力板 (2) 和活动板 (3) 之间的位置。 确保反冲弹簧组件处于水平居中位置。
Show/hide table
图 6 g00498784 Show/hide table组装期间,需要数吨的力才能压缩反冲弹簧。
请勿压缩弹簧组件,直到工具上的盖已关闭。
反冲弹簧在负载下可能会扭曲并脱离工具,从而导致人身伤亡。
- 关闭工具 (A) 上的盖 (7)。 使用工具 (B) 稍稍压缩反冲弹簧组件。
Show/hide table
图 7 g00889063 - 通过工具 (A) 端部的开口,从缓冲弹簧的固定杆端部拆下内六角头螺栓和锁片 (8)。
- 使用工具 (D) 拆下螺母 (6)。 释放反冲弹簧组件上的力。
- 打开工具 (A) 上的盖。 将适当的起吊设备连接到反冲弹簧组件,然后从工具 (A) 拆下反冲弹簧组件。
Show/hide table
图 8 g02723074 - 分离反冲弹簧组件的部件。 拆下螺母 (6)、履带调节器 (12)、板 (9)、弹簧 (10) 和支架 (11)。
Show/hide table
反冲弹簧组件的弹簧需要数吨的力才能压缩。 当螺母位于固定连杆末端时,请勿尝试压缩或释放弹簧的张力。 固定连杆或螺母上螺纹的损坏可造成组件带有弹力分离,从而导致人身伤亡。 |
Caterpillar Information System:
Selective Catalytic Reduction Retrofit Aftertreatment - Airless Dosing Event Codes
C32 Marine Auxiliary Engine Cold Weather Operation
320 GC, 320 and 323 Excavator Work Tool Operation - If Equipped
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Gas Pressure Regulator Solenoid - Remove and Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Gas Pressure Regulator Solenoid - Disassemble
CX38-P892 Well Servicing Transmission Gear Pump (Transmission)
CX38-P892 Well Servicing Transmission Relief Valve (Transmission Hydraulic Control)
C32 Marine Engine Maintenance Interval Schedule
Sub-Base Tank Water Retention Rework for Certain C4.4 Generator Sets {1000, 1273} Sub-Base Tank Water Retention Rework for Certain C4.4 Generator Sets {1000, 1273}
C32 Marine Auxiliary Engine Overhaul (Top End)
CX38-P892 Well Servicing Transmission Relief Valve (Torque Converter Outlet) Pressure - Test
330 GC and 330 Excavator Boom and Stick Linkage - Lubricate - VA Boom (If Equipped)
320GC, 320 and 323 Excavators Machine Systems Recoil Spring - Assemble
320 GC, 320 and 323 Excavator Machine Systems Main Hydraulic Pump
C32 Marine Auxiliary Engine Fuel System - Prime
G3516 Petroleum Engines Air Starting Motor - Remove
C9.3B Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
An Improved Multi-Function Joystick is Now Available for Certain Cat® Machines {5063, 5702, 5705} An Improved Multi-Function Joystick is Now Available for Certain Cat® Machines {5063, 5702, 5705}
320 GC, 320 and 323 Excavator Machine Systems General Information (Travel System)
320 GC, 320 and 323 Excavator Machine Systems Travel System
C32 Marine Auxiliary Engine Fuel System Secondary Filter - Replace
3516B Generator Set Engines with Dynamic Gas Blending Direct Fuel Control Mode - Test
320 GC, 320 and 323 Excavator Machine Systems Pump Control (Main Hydraulic) - Main Pump Regulator
320 GC, 320 and 323 Excavator Machine Systems Swivel