Catalyst (DOC) - Replace
Show/hide table
| NOTICE |
|---|
|
Ensure that all components are free of contaminants before installing. Contaminants may cause premature wear and reduced component service life. |
Note: Disposition and Recycling - Common components of exhaust aftertreatment devices include, but are not limited to, cordierite, silicon carbide, copper zeolite, vanadium, platinum, and palladium. After the devices are used in an engine exhaust flow, they can include some by-products that result from combustion. Follow applicable Federal, State, and local regulations when handling or discarding used aftertreatment devices.
- Remove Catalyst (DOC) hatch cover (1) nuts, bolts, and washers.
- Remove hatch cover (1) from the reactor unit.
- Remove gasket assembly from the sealing surface of the hatch cover.
- Carefully remove DOC catalyst assembly by removing the V band clamps. If necessary, repeat for other DOC catalysts.
- Carefully install DOC catalyst into the cabinet with new gaskets. Verify correct position.
- Apply final torque to V band clamps. Refer to Specifications, SENR3130, "Torque Specifications" for the proper torque.
- Replace all inner backing strip gaskets on the DOC catalyst cover.
- Install DOC cover assembly.
- Replace all bolts.
- Apply final torque to all bolts in a circular pattern. Refer to Specifications, SENR3130, "Torque Specifications" for the proper torque.
- Verify that all bolts are at the proper torque value.
Show/hide table
| |
| Illustration 1 | g03716811 |
Caterpillar Information System:
SCR Retrofit Aftertreatment Catalyst (DOC) - Clean/Inspect
SCR Retrofit Aftertreatment Fluid Recommendations
New Cylinder Head Available for 3512E Petroleum Well Service Engines {1100, 7555} New Cylinder Head Available for 3512E Petroleum Well Service Engines {1100, 7555}
Improved Venturi Tubes Are Now Used on Certain C27 and C32 Commercial Engines {1071} Improved Venturi Tubes Are Now Used on Certain C27 and C32 Commercial Engines {1071}
3500 and 3500B Engines Engine Operation
G3500H Generator Set Engine Engine Monitoring System
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting
SCR Retrofit Aftertreatment Before Starting Engine
3500C Marine Engines Engine Operation
New High-Pressure Fuel Pumps Are Now Used on Certain C175 Engines {125H} New High-Pressure Fuel Pumps Are Now Used on Certain C175 Engines {125H}
M0077752: Periodic Inspection and Maintenance required on 4C-9832 Engine Rollover Stand {1154} M0077752: Periodic Inspection and Maintenance required on 4C-9832 Engine Rollover Stand {1154}
3508B, 3512B, 3516B, 3512C and and 3516C Auxiliary Engines, Generator Set Engines, and Generator Sets Engine Operation
SCR Retrofit Aftertreatment Catalyst (SCR) - Clean/Inspect
3512B Generator Set Engines with Dynamic Gas Blending Event Codes
Marine Selective Catalytic Reduction (SCR) Retrofit Aftertreatment Diesel Exhaust Fluid Pump - Replace
A New Fuel Return Lines Are Used On Certain C18 Marine Engines {1274} A New Fuel Return Lines Are Used On Certain C18 Marine Engines {1274}
323F SA Excavator and 323F MHPU Machine Systems Cylinder Drift - Check - Empty Bucket
G3500H 50Hz Generator Sets Engine Air Cleaner Element - Replace
New Software Is Now Used For Certain 3516C Series Engines {1920} New Software Is Now Used For Certain 3516C Series Engines {1920}
A New Closed Crankcase Ventilation Drain Hose and Check Valve Are Now Used on Certain C18 Marine Separate Circuit Aftercooler Engines {1317} A New Closed Crankcase Ventilation Drain Hose and Check Valve Are Now Used on Certain C18 Marine Separate Circuit Aftercooler Engines {1317}
G3500H 60Hz Generator Sets Jacket Water Heater - Check
3500 Industrial and Generator Set Engines Engine Operation
G3516 TA Engine Electronic Service Tools
Installing Coolant Tubes and Clamps on Certain C175-16 Locomotive Engines {1307, 1380} Installing Coolant Tubes and Clamps on Certain C175-16 Locomotive Engines {1307, 1380}