Model View Illustrations
Show/hide table
| |
| Illustration 1 | g06109001 |
|
Retrofit Dosing Cabinet (1) SCR controller (2) Wiring harness connector to main DEF tank (3) Wiring harness connector to CEM (4) DEF vent port (5) AC power in (6) Breaker (7) Wiring harness (8) DEF outlet to CEM (9) Air outlet to CEM (10) Air inlet (11) DEF inlet (12) Wiring harness connector to engine ECM (13) 9-pin service tool connector (14) DEF pump (15) DEF tank (16) Retrofit control group | |
Show/hide table
| |
| Illustration 2 | g06139097 |
|
Retrofit Dosing Cabinet (17) Product Link Radio (Cellular/Satellite) (18) Display (19) Breaker (20) 3-pin power harness (21) 14-pin service tool connector (22) 9-pin interconnect harness (23) A5N2 Datalogger/Network Manager | |
Show/hide table
| |
| Illustration 3 | g06139103 |
|
Horizontal SCR Reactor Housing (25) Serial number plate (26) SCR catalyst access hatch (27) Mounting feet (28) Lifting eyes (29) DOC or DPF access hatch (30) Exhaust outlet | |
Show/hide table
| |
| Illustration 4 | g06139109 |
|
Internal view of Horizontal SCR Reactor Housing (31) DOC or DPF (32) Stationary mixing fans (33) SCR catalysts | |
Caterpillar Information System:
G3612 and G3616 Engines Fuel Shutoff Solenoid - Remove and Install
PM820, PM822, and PM825 Cold Planer Engine Supplement Battery - Remove and Install
SCR Retrofit Aftertreatment General Hazard Information
SCR Retrofit Aftertreatment Safety Messages
G3612 and G3616 Engines Cylinder Head - Install
Turbocharger Wastegate Hose On Certain C4.4 Engines {1052} Turbocharger Wastegate Hose On Certain C4.4 Engines {1052}
New Aftercooler Bonnets And Drain Line Are Now Used On Certain G3500 And CG170 Engines {1063, 1063} New Aftercooler Bonnets And Drain Line Are Now Used On Certain G3500 And CG170 Engines {1063, 1063}
PM820, PM822, and PM825 Cold Planer Rotor Coolant Level - Check
G3512 Generator Set Engine Turbocharger - Remove
PM820, PM822, and PM825 Cold Planer Rotor Bearing - Lubricate
Improved Procedure for the Installation of Swing Gear and Bearing Dust Seals on Certain Excavators {7063} Improved Procedure for the Installation of Swing Gear and Bearing Dust Seals on Certain Excavators {7063}
PM-620 and PM-622 Cold Planer Engine Supplement Muffler - Remove and Install
SR500 Generators Generator Installation
SCR Retrofit Aftertreatment Product Description
SCR Retrofit Aftertreatment Product Lifting
SCR Retrofit Aftertreatment Monitoring System
G3512 Generator Set Engine Turbocharger - Install
349F and 352F Excavator Machine System Diagnostic Trouble Codes
PM-620 and PM-622 Cold Planer Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Engines {1207} A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Engines {1207}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Sensor Mounting
C13 Engines for Caterpillar Built Machines ECM Software - Install
349F and 352F Excavator Machine System Sensor Signal (PWM) - Test
349F and 352F Excavators Machine System Specifications Stick Cylinder