Stick Cylinder
Show/hide table
| |
| Illustration 1 | g06105194 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 1 | 1 | 126-1971 Special Locknut | Use any one of the following methods to tighten the special locknut: Lubricate thread all around with 309-6932 Hydraulic Oil and tighten to or Lubricate thread with molybdenum disulphide and tighten to |
| 2 | 2 | 204-2845 Ring | Lubricate the inside diameter and the outside diameter with clean grease. |
| 3 | 1 | 495-8218 Seal As | Lubricate the inside diameter and the outside diameter with clean grease. |
| 4 | 1 | 204-2846 Ring | Lubricate the inside diameter and the outside diameter with clean grease. |
| 5 | 1 | 114-0763 Bushing | Outside diameter before assembly is Thickness is |
| 6 | 1 | Buffer Seal | Lubricate the sealing lip lightly with the fluid that is being sealed. |
| 7 | 1 | U-Cup Seal | Lubricate the sealing lip lightly with the fluid that is being sealed. |
| 8 | 1 | 165-9293 Lip Type Seal | Lubricate the sealing lip lightly with the fluid that is being sealed. |
| 9 | - | - | Before assembly, apply green Loctite 648 to the wiper seal groove. |
| 10 | 1 | 462-2010 Bushing | Bore before assembly is Installation depth is |
| A | 1 | 513-3690 Cylinder As | Bore diameter is |
| B | 1 | 513-3687 Rod As | Diameter is |
| C | 1 | 370-6693 Head | Bore over two lands is |
| 11 | 1 | 228-5618 Bushing | Bore before assembly is Installation depth is |
| 12 | 1 | 524-7886 Stop | Free linear movement of stop after assembly is |
| 13 | 2 | 143-1452 Retaining Ring | Maximum outside diameter of two retaining rings after assembly is |
| 14 | 1 | 200-3620 Seal Ring | The slit of the seal ring must turn in the direction of the piston. |
| 15 | 10 | 173-9684 Bolt | Torque to Turn to an additional angle of 30 ± 5 degree. |
Caterpillar Information System:
349F and 352F Excavator Machine System Sensor Signal (PWM) - Test
C13 Engines for Caterpillar Built Machines ECM Software - Install
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Sensor Mounting
A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Engines {1207} A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Engines {1207}
PM-620 and PM-622 Cold Planer Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
349F and 352F Excavator Machine System Diagnostic Trouble Codes
G3512 Generator Set Engine Turbocharger - Install
SCR Retrofit Aftertreatment Monitoring System
SCR Retrofit Aftertreatment Product Lifting
SCR Retrofit Aftertreatment Product Description
SR500 Generators Generator Installation
SCR Retrofit Aftertreatment Model View Illustrations
349F and 352F Excavator Machine System Sensor Supply - Test
349F and 352F Excavator Machine System Solenoid Valve - Test
349F and 352F Excavator Machine System Connector Contact Description
349F and 352F Excavator Machine System System Schematic
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train Speed Sensor and Mounting
349F and 352F Excavators Machine System Main Hydraulic System
349F and 352F Excavators Machine System Electronic Control System
349F and 352F Excavators Machine System Pilot Hydraulic System
349F and 352F Excavators Machine System Main Control Valve
349F and 352F Excavators Machine System Negative Flow Control System
349F and 352F Excavators Machine System Stick Hydraulic System
349F and 352F Excavators Machine System Bucket Hydraulic System