Fuel Shutoff Solenoid - Remove and Install
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 切断燃油供给。
Show/hide table
图 1 g06118036 Show/hide table图 2 g06118039 - 断开线束组件 (1) 和 (2)。
- 拆下两个螺栓 (5)。 拆下卡箍 (6) 并重新放置。
- 拆下其余的螺栓 (5) 和螺栓 (4)。 拆下燃油切断电磁阀 (3) 和密封垫。
- 按与拆卸相反的顺序安装燃油切断电磁阀 (3)。
- 拧紧螺栓 (4) 和 (5) 至扭矩为
150 ± 20 N·m (111 ± 15 lb ft) 。
- 拧紧螺栓 (4) 和 (5) 至扭矩为
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Engine Supplement Battery - Remove and Install
SCR Retrofit Aftertreatment General Hazard Information
SCR Retrofit Aftertreatment Safety Messages
G3612 and G3616 Engines Cylinder Head - Install
Turbocharger Wastegate Hose On Certain C4.4 Engines {1052} Turbocharger Wastegate Hose On Certain C4.4 Engines {1052}
New Aftercooler Bonnets And Drain Line Are Now Used On Certain G3500 And CG170 Engines {1063, 1063} New Aftercooler Bonnets And Drain Line Are Now Used On Certain G3500 And CG170 Engines {1063, 1063}
PM820, PM822, and PM825 Cold Planer Rotor Coolant Level - Check
G3512 Generator Set Engine Turbocharger - Remove
PM820, PM822, and PM825 Cold Planer Rotor Bearing - Lubricate
Improved Procedure for the Installation of Swing Gear and Bearing Dust Seals on Certain Excavators {7063} Improved Procedure for the Installation of Swing Gear and Bearing Dust Seals on Certain Excavators {7063}
PM-620 and PM-622 Cold Planer Engine Supplement Muffler - Remove and Install
Fuel Injection Pump Solenoid on Certain C4.4 and C6.6 Engines {1251, 1403} Fuel Injection Pump Solenoid on Certain C4.4 and C6.6 Engines {1251, 1403}
SCR Retrofit Aftertreatment Model View Illustrations
SR500 Generators Generator Installation
SCR Retrofit Aftertreatment Product Description
SCR Retrofit Aftertreatment Product Lifting
SCR Retrofit Aftertreatment Monitoring System
G3512 Generator Set Engine Turbocharger - Install
349F and 352F Excavator Machine System Diagnostic Trouble Codes
PM-620 and PM-622 Cold Planer Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Engines {1207} A New Drive Bearing Is Now Used on Certain 3406E, C11, C13, C15, C16, and C18 Engines {1207}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Sensor Mounting
C13 Engines for Caterpillar Built Machines ECM Software - Install
349F and 352F Excavator Machine System Sensor Signal (PWM) - Test