Camshaft Bearings - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 6V-4077 | Camshaft Bearing Tool Group | 1 |
| 125-2739 (1) | Bearing Pilot | 1 | |
| 125-2740 (1) | Back Up Plate | 1 | |
| 125-2741 (1) | Bearing Sleeve | 1 | |
| B | 8S-2241 | Camshaft Bearing Tool Group | 1 |
| C | 5P-5247 | Hydraulic Puller(2) | 1 |
| D | 8H-0684 | Ratchet Wrench | 1 |
Show/hide table
| (1) | Alternate Tooling for camshaft bearings with a large diameter |
| (2) | Do not exceed |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install camshaft bearing (1) on Tooling (A).
Note: Tooling (B) can be used to install the camshaft bearings when the flywheel housing and the front housing have been removed.
Show/hide table
Illustration 2 g02108639 Rear View
(X) Location of camshaft bearing joints
(Y) Location of oil holes - Position camshaft bearing (1) and Tooling (A) in the bore.
Note: The camshaft bearing joint must be on the horizontal centerline of the bore. The upper oil hole must be 20 ± 5 degrees above the horizontal centerline of the bore. The lower oil hole of the camshaft bearing must be 20 ± 5 degrees below the horizontal centerline of the bore. The camshaft bearing joints must face the inside the cylinder block.
Show/hide table
Illustration 3 g00578349 - Install Tooling (C) on Tooling (A) and pull the camshaft bearing into the bore.
Note: Tooling (D) can be used in place of Tooling (C).
- Check the bore of the camshaft bearing after installation. The bore must be
86.00 ± 0.06 mm (3.385 ± 0.002 inch) .
Show/hide table
| |
| Illustration 1 | g00578338 |
|
Typical example | |
End By:
- Install the camshafts.
Caterpillar Information System:
G3508J, G3516J, and G3520J Engines Camshaft Bearings - Remove
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Cylinder Head - Install
G3508J, G3516J, and G3520J Engines Camshaft - Install
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Cylinder Head - Remove
G3508J, G3516J, and G3520J Engines Camshaft - Remove
G3508J, G3516J, and G3520J Engines Cylinder Liner - Install
G3612 and G3616 Engines Crankshaft Main Bearings - Install
G3508J, G3516J, and G3520J Engines Cylinder Liner - Remove
G3612 and G3616 Engines Crankshaft Main Bearings - Remove
G3612 and G3616 Engines Camshaft - Remove
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Cylinder Liner Projection
794 AC Off-Highway Truck Machine Systems Solenoid and Manifold Valve (Steering) - Assemble
G3612 and G3616 Engines Crankshaft - Remove
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Turbocharger - Remove and Install
G3612 and G3616 Engines Crankshaft - Install
G3508J, G3516J, and G3520J Engines Crankshaft Main Bearings - Remove
G3508J, G3516J, and G3520J Engines Crankshaft Main Bearings - Install
320E and 323E Excavators Lifting Objects
Quick Start Wiring Guide for Certain G3300B Gas Compression Engines {1000, 1408, 1451, 1453} Quick Start Wiring Guide for Certain G3300B Gas Compression Engines {1000, 1408, 1451, 1453}
Cylinder Head Replacement Option for Certain C175 Petroleum Engines{1101} Cylinder Head Replacement Option for Certain C175 Petroleum Engines{1101}
XQ400 Power Module Engine Speed/Timing Sensor - Clean/Inspect
Initial Setup for Certified G3512 Generator Set Engines {1021} Initial Setup for Certified G3512 Generator Set Engines {1021}
XQ400 Power Module Gas Pressure Regulator - Test
C175–16 Locomotive Engine Valve Lash - Adjust - Hydraulic Lash Adjusters