Fluid End - Remove and Install
Removal Procedure
Show/hide table
Require Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | TBD     | Enerpac Well Stimulation all in One     | 1     |
B     | -     | Loctite 262     | -     |
C     | -     | Loctite Nickel Anti-Seize     | -     |
Start By:
- Remove the manifold (suction).
- Remove bolts (2) and clamp (1). Repeat for the remaining clamps.
Show/hide table
Table 2 Approximate weight of Fluid End (3)     Sales Model     Approximate Weight     WS273 XD
WSF273 XD    2093 kg (4614 lb)     WS305 XD
WSF305 XD    
3344 kg (7372 lb)    
Show/hide table
Illustration 1 | g03362870 |
Note: Clamp (1) halves are matched pairs. Place identification marks on clamp (1) for installation purposes.
- Use the provided lifting eyes and a suitable lifting device to remove fluid end well stimulation (3). Refer to Table 2 for the approximate weight of Fluid End (3). Remove nuts (4) and Fluid End (3) .
Show/hide table
Illustration 2 | g03362874 |
Show/hide table
Illustration 3 | g03362941 |
Installation Procedure
- Install the Fluid End (3) in the reverse order of removal.
- Apply Tooling (C) on the rods.
Show/hide table
Table 3 Torque of Nuts (4)     Sales Model     Nut (4) Torque     WS273 XD
WSF273 XD    
3661 N·m (2700 lb ft)    WS305 XD
WSF305 XD    
3661 N·m (2700 lb ft)    
Note: Check the length of each rod before installing fluid end (3). Refer to Disassembly and Assembly, " Rod - Remove and Install".
- Torque nuts (4) in sequence shown in Illustration 4 and 5. Refer to Table 3 for torque of nuts (4) .
Show/hide tableIllustration 4 g03494204
Triplex Well Stimulation Pumps.
Show/hide tableIllustration 5 g03645339
Quintuplex Well Stimulation Pumps.
- Apply Tooling (B) on bolts (2). Tighten bolts (2) to a torque of 108 N·m (80 lb ft).
- Apply Tooling (C) on the rods.
Caterpillar Information System:
2015/09/11 New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
Energy Storage System Plate Locations and Film Locations
Energy Storage System Safety
C7.1 Commercial Marine Engine V-Belt - Test
C7.1 Commercial Marine Engine Gear Group - Inspect
Sub-Base Tank Water Retention Rework for Certain C15, C18, and C9 Generator Sets{1273} Sub-Base Tank Water Retention Rework for Certain C15, C18, and C9 Generator Sets{1273}
C7.1 Commercial Marine Engine Flywheel Housing - Inspect
G3600 A4 Engines Maintenance Interval Schedule - G3600 Wellhead or Natural Gas Engines with a 7.6 :1 Compression Ratio
EMCP 4.4 Supervisory Control Panel Control Panel
EMCP 4.4 Supervisory Control Panel Plate Locations and Film Locations
EMCP 4.4 Supervisory Control Panel Model View Illustrations
EMCP 4.4 Supervisory Control Panel Electrical System
XQ35 Rental Generator Set Product Lifting
C7.1 Marine Engine Event Codes
3516E Generator Set Engine Air Inlet and Exhaust System Operation
3516E Generator Set Engine Turbocharger
Crankshaft Bearing Housing Assembly Instructions for Well Stimulation Pumps {1202, 5070} Crankshaft Bearing Housing Assembly Instructions for Well Stimulation Pumps {1202, 5070}
3516B Generator Set Engines with Dynamic Gas Blending Test Tools for the Cooling System
EMCP4.2B Setpoint Programming
C12.9 Marine Engines Product Lifting
EMCP4.2B Digital Input Programming
320D2 and 323D2 Excavators Machine Systems Specifications Shuttle Valve (Pilot Lines)
2015/09/11 Current Transformer Coils on Certain C7.1 and C4.4 Marine Generator Sets {4476}
C1.7 and C2.2 Industrial Engines Monitoring System - Engine Warning Indicators