A New Damper Group Is Used on Certain C175 Petroleum Engines {1205}
- Engine:
- C175-16 (S/N: P6L1-UP)
Description of Change: The new damper group provides additional protection against oil leaks.
Adaptable To: The new 362-7672 Damper Gp replaces the existing 317-1639 Damper Gp. The new damper group is adaptable back to first production on the serial numbers listed above.
Refer to Table 1 for a list of part numbers needed to install the new damper group.
Show/hide table
New Part Number     | Description     | Quantity     |
146-3173     | Dowel     | 2     |
240-0312     | Bolt     | 12     |
241-6157     | Plug     | 2     |
362-7672     | Damper Gp     | 1     |
370-6871     | Adapter     | 1     |
397-2457     | Dowel     | 1     |
478-1756     | Hard Washer     | 12     |
6V-9028     | O-Ring Seal     | 2     |
Damper Group Installation Procedure
- Set cylinder 1 to Top Dead Center (TDC).
- Remove the existing damper guard, damper, hub, and seals. Refer to Disassembly and Assembly, UENR5600 for the proper procedures.
- Install the 241-6157 Plugs into the supply and return holes in the crankshaft.
- For Type I Crankshafts: Install a 397-2457 Dowel into the flat side of the 370-6871 Adapter. Then, install a 146-3173 Dowel into the side of the hub with the extension.
For Type II Crankshafts: Install a 146-3173 Dowel into both sides of the 370-6871 Adapter .
- Install the 362-7672 Damper Gp .
- Pre-torque the damper bolts in the order shown in Illustration 1.
Torque for the 240-0312 Bolts ... 350 ± 50 N·m (258 ± 37 lb ft)
Show/hide table
Illustration 1 | g03830358 |
- Torque the damper bolts in the order shown in Illustration 1.
Torque for the 240-0312 Bolts ... 800 ± 100 N·m (590 ± 74 lb ft)
Caterpillar Information System:
3512C Generator Set Engine Exhaust Elbow - Remove and Install
2015/07/24 New Fuel Lines and Mounting Hardware Are Used On Certain 3500 Engines {1252}
3412 Generator Set Electrical Power Supply - Test
C280-08 Tier 4 Engine Housing (Front) - Remove and Install
3412 Generator Set ECM/Personality Module - Test
2015/06/05 A New Prelubrication Oil Pump Is Used on Certain G3500 Engines {1319}
2015/07/07 New Piston and Liner Components Are Available For Certain G3516H Engines {1214, 1215, 1216, 1222, 1239}
2015/06/26 Cat® Reman Announces Additions to Several Engine Component Portfolios {108F, 1210, 1290, 1405, 7490}
2015/06/25 Cat® Reman Announces Additions to Several Engine Component Portfolios {108F, 1210, 1290, 1405, 7490}
794 AC Off-Highway Truck Field Assembly Platform - Install
3516B Generator Set Engines with Dynamic Gas Blending Electronic Service Tool Does Not Communicate
C280-08 Tier 4 Engine Crankshaft Rear Gear - Remove and Install
G3606 and G3608 Engines Water Pump Seal - Install
3412 Generator Set Engine Speed - Test
797F Off-Highway Truck Field Assembly Tire and Rim (Front) - Install
797F Off-Highway Truck Field Assembly Tire and Rim (Rear) - Install
G3606 and G3608 Engines Water Manifold - Remove and Install
C4.4 and C7.1 Engines Intake Manifold Air Temperature Is High
Replacement Procedure For the Camshaft On the C8.7 Marine Engine{1210} Replacement Procedure For the Camshaft On the C8.7 Marine Engine{1210}
2015/06/05 Cat® Reman Now Offers Camshafts for Certain G3516H Engines {1210}
C280-08 Tier 4 Engine Housing (Rear) - Remove and Install
794 AC Off-Highway Truck Field Assembly Ladder - Install
3512C Generator Set Engine Exhaust Manifold - Remove and Install
C280 Marine Engines Speed/Timing - Test