Water Pump Seal - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 冲头总成 | 1 |
B | 8T-3034 | 水泵密封起子 | 1 |
C | 6V-1541 | 快速固化底漆 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 用钢丝棉去除轴 (6) 上的沉积物和腐蚀。
注: 不要使用会在泵轴上留下明显划痕的砂纸。
- 检查轴的碳精密封区域。 除非该区域的点蚀和腐蚀仍可为冷却液在橡胶轴和泵轴之间提供流动的通道,否则请更换轴。 管轴上该区域的光面表示已在轴上旋转碳精密封。 安装新的密封件之前,请在抛光区域使用细砂纸。
- 使用工具 (C) 清洁轴 (6) 和壳体内的密封件沉头孔。
- 将清洁的水放在陶瓷密封 (9) 的 O 形密封圈上。 使用工具 (B) 固定壳体内的陶瓷密封。 安装陶瓷环,使光面朝向碳精密封。
- 将碳精密封 (8) 浸在清洁的水中。 将碳精密封 (8) 安装在轴 (6) 上。 使用工具 (A) 将碳精密封推到轴上。 推动碳精密封,直到表面接触到陶瓷密封的表面。
- 将弹簧 (7) 放在轴 (6) 上的合适位置。
- 将叶轮 (3) 放在轴上的合适位置。 安装螺栓 (4) 和垫圈 (5)。
- 将螺栓 (4) 拧紧至扭矩为
360 ± 50 N·m (265 ± 35 lb ft) 。 用锤子敲击螺栓头。 再次拧紧螺栓。 重复这一步骤,直至扭矩不再变化。 - 在壳体上安装新 O 形密封圈 (2)。 将皂液涂在 O 形密封圈上。
- 在水泵上安装壳体 (1)。 确保壳体的方向正确。
- 向冷却系统加注冷却液到正确的液位。 请参阅操作和维护手册。
Show/hide table
图 2 g03842366 - 安装弯头 (1)、螺栓 (2) 和螺栓 (3)。
- 安装管 (6)、螺栓 (5) 和螺栓 (4)。
- 加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"以了解正确的排放和加注步骤。
Show/hide table
图 1 | g00545616 |
Caterpillar Information System:
2015/06/05 A New Damper Group Is Used on Certain C175 Petroleum Engines {1205}
3512C Generator Set Engine Exhaust Elbow - Remove and Install
2015/07/24 New Fuel Lines and Mounting Hardware Are Used On Certain 3500 Engines {1252}
3412 Generator Set Electrical Power Supply - Test
C280-08 Tier 4 Engine Housing (Front) - Remove and Install
3412 Generator Set ECM/Personality Module - Test
2015/06/05 A New Prelubrication Oil Pump Is Used on Certain G3500 Engines {1319}
2015/07/07 New Piston and Liner Components Are Available For Certain G3516H Engines {1214, 1215, 1216, 1222, 1239}
2015/06/26 Cat® Reman Announces Additions to Several Engine Component Portfolios {108F, 1210, 1290, 1405, 7490}
2015/06/25 Cat® Reman Announces Additions to Several Engine Component Portfolios {108F, 1210, 1290, 1405, 7490}
794 AC Off-Highway Truck Field Assembly Platform - Install
3516B Generator Set Engines with Dynamic Gas Blending Electronic Service Tool Does Not Communicate
3412 Generator Set Engine Speed - Test
797F Off-Highway Truck Field Assembly Tire and Rim (Front) - Install
797F Off-Highway Truck Field Assembly Tire and Rim (Rear) - Install
G3606 and G3608 Engines Water Manifold - Remove and Install
C4.4 and C7.1 Engines Intake Manifold Air Temperature Is High
Replacement Procedure For the Camshaft On the C8.7 Marine Engine{1210} Replacement Procedure For the Camshaft On the C8.7 Marine Engine{1210}
2015/06/05 Cat® Reman Now Offers Camshafts for Certain G3516H Engines {1210}
C280-08 Tier 4 Engine Housing (Rear) - Remove and Install
794 AC Off-Highway Truck Field Assembly Ladder - Install
3512C Generator Set Engine Exhaust Manifold - Remove and Install
C280 Marine Engines Speed/Timing - Test
C280-08 Tier 4 Engine Centrifugal Oil Filter - Remove and Install