Piston and Rings
Show/hide table
| |
| Illustration 1 | g03538917 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| Install the rod and piston group in the engine with the part number of the forging for the rod assembly to the rear of the engine. The rear of the engine is the flywheel end of the engine. Lubricate the rod and piston group with clean engine oil before you insert the rod and piston group into the block. | |||
| 1 | 1 | 447-5626 Piston Ring | Install the top piston ring with the side marked "UP-1" toward the top of the piston. The blue colored stripe faces to the right of the ring end gap. |
| When the new top piston ring is installed in a cylinder liner bore with bore size of |
|||
| Thickness is |
|||
| 2 | 1 | 467-1177 Piston Ring | Install the intermediate piston ring with the side marked "UP-2" toward the top of the piston. The red-colored stripe faces to the right of the piston ring end gap. |
| When the new intermediate piston ring is installed in a cylinder liner bore with bore size of |
|||
| Width of groove in new piston body assembly for intermediate piston ring is |
|||
| Thickness is |
|||
| 3 | 1 | 262-2891 Piston Ring | The oil control piston ring has a spring that is installed with the ring. The gap in the spring should be a distance of 180 degrees from the ring end gap when the oil control piston ring is assembled. The orange colored portion can be to the right or to the left of the ring end gap. |
| When the new oil control piston ring is installed in a cylinder liner bore with bore size of |
|||
| Width of groove in new piston body assembly for oil control piston ring is |
|||
| Thickness is |
|||
| After the piston rings have been installed, rotate the piston rings so that the end gaps are 120 degrees from each other. | |||
| Thoroughly lubricate the entire piston prior to assembly into the cylinder block with clean engine oil. | |||
| 4 | 1 | 524-7952 Piston Pin | Thoroughly lubricate the piston pin with clean engine oil prior to assembly. |
| Outside diameter is |
|||
| Inside diameter is |
|||
| Length is |
|||
Caterpillar Information System:
C9.3 Marine Engines Pressure Sensor (Auxiliary)
XQ400 Power Module Voltage Regulators
C4.4 Generator Sets Fuel System Secondary Filter - Replace
3412 Generator Set Engine Shutdown Occurs Intermittently
C4.4 Generator Sets Engine Oil and Filter - Change
794 AC Off-Highway Truck Brakes, Indicators and Gauges - Test
3412 Generator Set Engine Overspeeds
3412 Generator Set Engine Misfires, Runs Rough or Is Unstable
C4.4 Generator Sets Generator Operation
3412 Generator Set Engine Does Not Crank
3412 Generator Set Engine Cranks but Does Not Start
3412 Generator Set Coolant Temperature Is Low
C8.7 Marine Engine Engine Support (Front) - Remove and Install
C8.7 Marine Engine Engine Support (Rear) - Remove and Install
G3612 and G3616 Engines Crankcase Pressure Sensor - Remove and Install
3512E Tier 4 Final Engines for Land Electric Drilling Fuel Rail Pressure Problem
XQC1200 and XQC1600 Power Modules Crankcase Pressure Sensor - Remove and Install
2015/02/27 A New Method to Prevent Water from Being Trapped in Fuel Heaters is Available {1250, 1296}
C8.7 Marine Engine Water Temperature Regulator - Remove and Install
New Sensor Kit Is Now Used On Certain Cat® Products {1000, 1439, 1718, 1906, 1907, 1912, 1917, 1923, 1924, 1925, 1929, 7400, 7422} New Sensor Kit Is Now Used On Certain Cat® Products {1000, 1439, 1718, 1906, 1907, 1912, 1917, 1923, 1924, 1925, 1929, 7400, 7422}
C18 Generator Set Walk-Around Inspection
C18 Generator Set Water Pump - Inspect
C18 Generator Set Plate Locations and Film Locations
Jacket Water Lines May Leak On Certain 3500 Power Modules{1380} Jacket Water Lines May Leak On Certain 3500 Power Modules{1380}