Engine Air Filter Service Indicator - Inspect
空气滤清器维修指示器可能装在空气滤清器滤芯上或在较远的地方。
Show/hide table
图 1 | g00760342 |
维修指示灯 |
某些发动机可能装有不同的维修指示器。
观察维修指示器。 发生以下情况时,要清洁或更换空气滤清器滤芯:
- 黄色膜片进入红色区域。
- 红色柱塞锁定在可见位置。
- 空气阻力达到
3.75 kPa (15 inch of H2O) 。
Show/hide table
图 2 | g00760341 |
曲轴箱通风用空气滤清器上的保养指示器 |
某些发动机配备了曲轴箱通风用进气滤清器。 这种空气滤清器安装在凸轮轴盖上。 发生以下情况时,要清洁或更换空气滤清器滤芯:
- 黄色膜片进入红色区域。
- 红色柱塞锁定在可见位置。
- 空气阻力达到
0.25 kPa (1 inch of H2O) 。 - 该空气滤清器浸透了机油。
每天检查维修指示器是否有裂纹,孔洞或松动的接头。 如果出现任何此类情况,更换保养指示器。
维修指示器是重要的仪器。
- 将保养指示器抽真空(抽吸)。
- 使维修指示器复位。
如果黄色芯没有锁定在最大真空位置或如果保养指示器不容易复位,就应该更换新保养指示器。 如果新的维修指示器也不能复位,则维修指示器的接头可能已堵住。
Show/hide table
图 3 | g00351792 |
多孔滤清器 |
多孔滤清器是用来安装保养指示器的接头的一部分。 检查滤清器是否清洁。 如有必要,清洁此滤清器。 使用压缩空气或清洁、不易燃的溶剂。
注: 安装保养指示器时,拧得过紧可能使保养指示器顶部开裂。 拧紧维修指示器至扭矩为
不管运转情况如何,每年都要更换维修指示器。
Caterpillar Information System:
XQC1200 and XQC1600 Power Modules Water Pump - Disassemble
G3500 Engines Fluid Recommendations
G3500 Engines Refill Capacities
320D and 323D Excavators Machine System Specifications Auxiliary Hydraulic Lines
2014/07/25 Capturing Engine Stop Messages and Idle Information on All Caterpillar Products Equipped with Product Link 522 {7606}
G3500 Engines Welding on Engines with Electronic Controls
C8.7 Marine Engines Engine Oil Pressure - Test
Inspection and Installation Procedure for C175 Exhaust Bellows {1059, 1061} Inspection and Installation Procedure for C175 Exhaust Bellows {1059, 1061}
C8.7 Marine Engines Vibration Damper - Check
3516C and C175-16 Engines Selective Catalytic Reduction DEF Tank Level Is Low
455-1184 Major Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1184 Major Overhaul Foundational Kit for C18 Marine Engines{1000}
C8.7 Marine Engines Cooling System - Test
3516C and C175-16 Engines Selective Catalytic Reduction Sensor (Data Link Type) - Test
XQC1200 and XQC1600 Power Modules Water Pump - Assemble
XQC1200 and XQC1600 Power Modules Electronic Unit Injector - Remove
Bench Test Procedure for Hydraulic Piston Pumps{0599, 5070, 5070} Bench Test Procedure for Hydraulic Piston Pumps{0599, 5070, 5070}
XQC1200 and XQC1600 Power Modules Electronic Unit Injector - Install
XQC1200 and XQC1600 Power Modules Cylinder Head - Remove
XQC1200 and XQC1600 Power Modules Cylinder Head - Install
3516C and C175-16 Engines Selective Catalytic Reduction SCR Catalyst Temperature Sensor - Test
XQC1200 and XQC1600 Power Modules Inlet and Exhaust Valve Springs - Remove and Install
XQC1200 and XQC1600 Power Modules Inlet and Exhaust Valves - Remove and Install
3516C and C175-16 Engines Selective Catalytic Reduction Clean Emissions Module Has High Oxygen Level
XQC1200 and XQC1600 Power Modules Inlet and Exhaust Valve Guides - Remove and Install