Electric Starting Motor - Remove and Install
Show/hide table
发动机的意外起动会对在设备上工作的人员造成伤害或死亡。 |
- 将蓄电池断路开关转到断开位置。
- 在与电动起动马达和电磁阀相连的线束组件上作识别标记。
Show/hide table
图 1 g02844537 典型示例 - 从电动起动马达和电磁阀上断开线束组件。
- 支撑电动起动马达 (3)。
- 将螺栓 (2) 从电动起动马达 (3) 上拆下。
- 拆下电动起动马达 (3)。
- 如有安装有密封垫,拆下密封垫 (4)。
Show/hide table
图 2 | g02844537 |
典型示例 |
- 如有必要,将新的密封垫 (4) 定位到电动起动马达 (3) 上。
- 将电动起动马达 (3) 定位到飞轮壳 (1) 上。
注: 确保电动起动马达正确落座在起动马达座中。
- 将螺栓 (2) 安装到电动起动马达 (3) 上。 拧紧螺栓至扭矩为
45 N·m (33 lb ft) 。 - 将线束组件连接到电动起动马达及电磁阀上。
- 将蓄电池断路开关转到接通位置。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Alternator - Install
C3.4B Engines for Caterpillar Built Machines Alternator - Remove
C3.4B Engines for Caterpillar Built Machines Fan Drive - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fan - Remove and Install
C3.4B Engines for Caterpillar Built Machines Idler Pulley - Remove and Install
C3.4B Engines for Caterpillar Built Machines Alternator Belt - Remove and Install
C3.4B Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet Manifold Pressure Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet Manifold Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Pressure Sensor (Exhaust Back Pressure) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Exhaust Manifold Temperature Sensor for NRS
C3.4B Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
Installation of the 459-5764 Engine Electronics {1901, 1920} Installation of the 459-5764 Engine Electronics {1901, 1920}
XQC1200 and XQC1600 Power Modules Water Temperature Regulators - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C175-16 PETROLEUM ENGINES Fuel Control Valve - Remove and Install - Primary
XQC1200 and XQC1600 Power Modules Water Pump - Remove and Install
2014/06/20 A Shorter Plug Is Required on the Water Pump Group of Certain C-9 Engines {1361, 7553}
C8.7 Marine Engine Oil Cooler Core - Check/Clean/Test - Gear Oil Cooler - If Equipped
XQC1200 and XQC1600 Power Modules Water Temperature Regulators - Remove and Install - Auxiliary Water System
C175-16 PETROLEUM ENGINES Fuel Pump (High Pressure) - Remove and Install
C8.7 Marine Engine Belt - Inspect
2014/06/13 New Engine Software Is Used on Certain C175 Electric Power Generation (EPG) Engines {1901, 1920}