Water Pump - Remove and Install
- Drain the cooing system until the level of the coolant is below the water temperature regulator housing. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining and filling procedure.
Show/hide table
Illustration 1 g03687176 - Remove tube assembly (1). Remove the O-ring seals (not shown).
Show/hide table
Illustration 2 g03687379 - Disconnect harness assembly (2).
Show/hide table
Illustration 3 g03687381 - Remove tube clamp (3).
Show/hide table
Illustration 4 g03687385 Show/hide tableIllustration 5 g03687398 - Remove bolts (4) and remove or reposition tube and flange assembly (5). Remove gasket (6).
Show/hide table
Illustration 6 g03687402 - Remove damper guard (7). Using two people, remove bolts (8) and (10) and remove water pump (9). The weight of water pump (9) is approximately
40 kg (88 lb) . Remove the gasket and the O-ring seal (not shown).
- Install water pump (9) in the reverse order of removal.
Caterpillar Information System:
C175-16 PETROLEUM ENGINES Fuel Control Valve - Remove and Install - Primary
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
XQC1200 and XQC1600 Power Modules Water Temperature Regulators - Remove and Install
Installation of the 459-5764 Engine Electronics {1901, 1920} Installation of the 459-5764 Engine Electronics {1901, 1920}
C3.4B Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Alternator - Install
C3.4B Engines for Caterpillar Built Machines Alternator - Remove
C3.4B Engines for Caterpillar Built Machines Fan Drive - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fan - Remove and Install
C3.4B Engines for Caterpillar Built Machines Idler Pulley - Remove and Install
C3.4B Engines for Caterpillar Built Machines Alternator Belt - Remove and Install
2014/06/20 A Shorter Plug Is Required on the Water Pump Group of Certain C-9 Engines {1361, 7553}
C8.7 Marine Engine Oil Cooler Core - Check/Clean/Test - Gear Oil Cooler - If Equipped
XQC1200 and XQC1600 Power Modules Water Temperature Regulators - Remove and Install - Auxiliary Water System
C175-16 PETROLEUM ENGINES Fuel Pump (High Pressure) - Remove and Install
C8.7 Marine Engine Belt - Inspect
2014/06/13 New Engine Software Is Used on Certain C175 Electric Power Generation (EPG) Engines {1901, 1920}
2014/06/13 Additional Diesel Particulate Filter (DPF) Ash Service Cleaning Interval Information Is Now Used On Certain Tier 4 Interim and Tier 4 Final C7.1 - C18 Engines {108F}
797 Off-Highway Truck Manual Lowering (Powered Stairway) - Test - If Equipped
421-1011 Valve Recession Tool Group used on G3500 C, E, ; H Engines{0374, 0599, 0701, 0703, 1100} 421-1011 Valve Recession Tool Group used on G3500 C, E, & H Engines{0374, 0599, 0701, 0703, 1100}
797 Off-Highway Truck Hydraulic System Hoist System - Oil Makeup - If Equipped
2014/07/03 New Accessory Drives Are Used on Certain 3500 Machine Engines {1207}
Retrofit SCR Aftertreatment Maintenance Interval Schedule