Fan - Remove and Install
开始:
- 拆下交流发电机皮带。 有关正确的步骤,请参阅拆解和装配, "交流发电机皮带 - 拆卸和安装"。
- 拆下螺母 (1)。
- 拆下风扇 (2)。
注: 记录风扇的方位。
- 卸下风扇适配器 (3)。
- 卸下风扇皮带轮 (4)。
- 如有必要,将螺柱 (5) 从风扇驱动 (6) 上拆下。
Show/hide table
图 1 | g02829456 |
典型示例 |
- 确保所有部件无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
Show/hide table
图 2 g02829456 典型示例 - 如有必要,将螺柱 (5) 安装到风扇驱动 (6) 上。 将双头螺栓 (5) 拧紧至扭矩为
11 N·m (97 lb in) 。 - 如果先前有将螺柱 (5) 从风扇驱动 (6) 上拆下, 检查风扇驱动器螺柱是否正确安装。 将双头螺栓 (5) 拧紧至扭矩为
25 N·m (221 lb in) 。 - 安装风扇皮带轮 (4)。
- 安装风扇适配器 (3)。
- 安装风扇 (2)。
注: 确保风扇朝向正确。
- 检查锁定螺母 (1) 的状况。 如有必要,更换锁定螺母。 安装锁定螺母 (1)。 拧紧锁定螺母 (1) 至扭矩为
22 N·m (195 lb in) 。
结束:
- 安装交流发电机皮带。 有关正确的步骤,请参阅拆解和装配, "交流发电机皮带 - 拆卸和安装"。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Idler Pulley - Remove and Install
C3.4B Engines for Caterpillar Built Machines Alternator Belt - Remove and Install
C3.4B Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet Manifold Pressure Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet Manifold Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Pressure Sensor (Exhaust Back Pressure) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Exhaust Manifold Temperature Sensor for NRS
C3.4B Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C3.4B Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fan Drive - Remove and Install
C3.4B Engines for Caterpillar Built Machines Alternator - Remove
C3.4B Engines for Caterpillar Built Machines Alternator - Install
C3.4B Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
Installation of the 459-5764 Engine Electronics {1901, 1920} Installation of the 459-5764 Engine Electronics {1901, 1920}
XQC1200 and XQC1600 Power Modules Water Temperature Regulators - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C175-16 PETROLEUM ENGINES Fuel Control Valve - Remove and Install - Primary
XQC1200 and XQC1600 Power Modules Water Pump - Remove and Install
2014/06/20 A Shorter Plug Is Required on the Water Pump Group of Certain C-9 Engines {1361, 7553}
C8.7 Marine Engine Oil Cooler Core - Check/Clean/Test - Gear Oil Cooler - If Equipped