Inlet Manifold Pressure Sensor - Remove and Install
- 将导线线束组件 (4) 从进气歧管压力传感器 (1) 上断开。
- 将螺母 (2) 从进气歧管压力传感器 (1) 上拆下。
- 从进气歧管上拆下进气歧管压力传感器 (1)。
- 将 O 形密封圈 (3)(未显示)从进气歧管压力传感器 (1) 上拆下。
Show/hide table
图 1 | g03794049 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保进气歧管压力传感器没有磨损或损坏。 如果进气歧管压力传感器磨损或损坏,请将进气歧管压力传感器作为一个整体进行更换。
Show/hide table
图 2 g03794049 - 将新的 O 形密封圈 (3)(未显示)安装到进气歧管压力传感器 (1) 上。
- 将进气歧管压力传感器 (1) 安装到进气歧管上。
- 将螺母 (2) 安装到进气歧管压力传感器 (1) 上。 拧紧螺母至扭矩为
10 N·m (89 lb in) 。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Inlet Manifold Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Pressure Sensor (Exhaust Back Pressure) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Exhaust Manifold Temperature Sensor for NRS
C3.4B Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C3.4B Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Crankshaft Timing Ring - Remove and Install
C3.4B Engines for Caterpillar Built Machines Crankshaft - Install
C3.4B Engines for Caterpillar Built Machines Crankshaft - Remove
C3.4B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove and Install
C3.4B Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
C3.4B Engines for Caterpillar Built Machines Alternator Belt - Remove and Install
C3.4B Engines for Caterpillar Built Machines Idler Pulley - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fan - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fan Drive - Remove and Install
C3.4B Engines for Caterpillar Built Machines Alternator - Remove
C3.4B Engines for Caterpillar Built Machines Alternator - Install
C3.4B Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
Installation of the 459-5764 Engine Electronics {1901, 1920} Installation of the 459-5764 Engine Electronics {1901, 1920}
XQC1200 and XQC1600 Power Modules Water Temperature Regulators - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install