Radiator - Remove and Install - Front
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 439-3940     | 连杆支架     | 2     |
开始:
- 拆卸冷却系统组件护罩。
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且冷却系统压力盖已经冷却到可以徒手触摸时,再慢慢拆下冷却系统压力盖以释放压力。 不要试图在冷却液还热的时候去拧紧软管接头,软管会脱落而造成灼伤。 警告:冷却系统的冷却液添加剂含碱。 应避免它与皮肤和眼睛接触。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
- 参考操作和保养手册, "液压系统油 - 更换",以了解正确的排放和加注步骤。
- 参考操作和保养手册, "冷却系统冷却液(ELC)- 更换"以了解正确的排放和加注步骤。
- 拆下面板 (1) 。
Show/hide table
图 1 | g03635043 |
典型示例 |
- 断开软管 (2) 。 拆下油箱组件 (3) 。
Show/hide table
图 2 | g03635056 |
- 断开软管 (4) 。
Show/hide table
图 3 | g03635062 |
- 断开管 (5) 和软管 (6) 。
Show/hide table
图 4 | g03635065 |
- 卸下支架 (7) 。
Show/hide table
图 5 | g03635067 |
- 拆下所有螺栓 (8) 和 (9) 。
Show/hide table
图 6 | g03521737 |
- 拆下螺栓 (10) 和 (11) 。
Show/hide table
图 7 | g03522118 |
- 拆下螺栓 (12) 和 (13) 。
Show/hide table
图 8 | g03522119 |
- 拆下螺栓 (14) 。
Show/hide table
图 9 | g03522121 |
- 将工具 (A) 和适当的起吊设备连接到面板盖 (15) 上。 面板盖 (15) 的重量约为 41 kg (90 lb)。
Show/hide table
图 10 | g03522159 |
- 拆下其余的螺栓 (16) ,然后拆下面板盖 (15) 。
Show/hide table
图 11 | g03522160 |
- 将工具 (A) 和适当的起吊设备连接到上面板 (17) 上。 上面板 (17) 的重量约为 23 kg (50 lb)。 拆下上面板 (17) 。
Show/hide table
图 12 | g03523517 |
- 拆下软管 (18) 。 拆下螺栓 (19) 。 拆下下面板盖 (20) 。
Show/hide table
图 13 | g03523560 |
- 拆下底部防护罩 (21) 。
Show/hide table
图 14 | g03530252 |
- 拆下盖 (22) 。 断开软管 (24) 并拆下安装螺栓 (23) 。
Show/hide table
图 15 | g03530254 |
- 将工具 (A) 和适当的起吊设备连接到散热器 (25) 。 散热器 (25) 的重量约为 36 kg (80 lb)。 拆下散热器 (25) 。
Show/hide table
图 16 | g03530256 |
安装步骤
- 按与拆卸相反的顺序安装散热器 (25) 。
Caterpillar Information System:
374F Excavator Camera Harness - Disconnect and Connect
374F Excavator Machine Systems BLCV and SLCV - Calibrate - If Equipped
390F Excavator Hydraulic Oil Cooler - Remove and Install - Front
390F Excavator Hydraulic Oil Cooler - Remove and Install - Rear
349F and 352F Excavators Machine System Specifications Pilot Lines
374F Excavator Leaving the Machine
390F Excavator Aftercooler - Remove and Install
390F Excavator Enclosure (Cooling System Package) - Remove and Install
2014/02/26 An Improved Engine Oil Filter Element Is Used for Certain C175 Commercial Engines {1308}
390F Excavator C18 Engine Supplement Manifold (DEF Heater) - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Gear Group (Rear) - Remove
390F Excavator Refrigerant Compressor - Remove and Install
Required Parts for Installing Turbochargers on Certain 2007 On-Highway Truck Engines {1052, 1053} Required Parts for Installing Turbochargers on Certain 2007 On-Highway Truck Engines {1052, 1053}
C8.7 Marine Engines Air Inlet and Exhaust System
C3.4B Engines Switch Circuits - Test - Engine Oil Pressure Switch
349F and 352F Excavators Machine System Specifications Hydraulic Tank Mounting
C3.4B Engines Valve Position - Test
349F and 352F Excavators Machine System Specifications Air Conditioner Lines
390F Excavator Radiator - Remove and Install - Rear
C27 and C32 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
2014/05/30 New Rocker Arms Are Used for Certain C27 and C32 Machine Engines {1102, 1123}
C27 and C32 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
G3600 A4 Engines Safety Messages
390F MHPU Mobile Hydraulic Power Unit Machine System Main Hydraulic Pump