Manifold (DEF Heater) - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 207-1601     | 橡胶润滑剂     | -     |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 拆下盖组件 (1) 和盖 (2) 。
Show/hide table
图 1 | g03631576 |
- 拆下螺栓 (3) 和托架 (4) 。
Show/hide table
图 2 | g03631596 |
- 钳断软管 (7) 。
Show/hide table
图 3 | g03631623 |
注: 请参阅专门说明书, REHS8231, "柴油机排气处理液 (DEF) 接头的拆卸步骤",了解软管组件 (8) 的正确拆卸步骤。
- 拆下夹子 (5) 和 (9) 。 断开线束组件 (6) 。 拆下软管组件 (8) 和软管 (7) 。
- 拆下电缆扎带 (10) ,然后断开线束组件 (11) 。
Show/hide table
图 4 | g03631636 |
- 拆下螺栓 (12) 、板 (13) 、歧管 (14) 和垫片(未显示)。
Show/hide table
图 5 | g03631656 |
- 将滤清器组件 (15) 从歧管组件 (14) 上拆下。
Show/hide table
图 6 | g03631661 |
箭头指示滤清器组件 (11) 的拆卸方向。 |
Show/hide table
图 7 | g03631678 |
注: 要将滤清器组件 (15) 从歧管组件 (14) 上拆下,拉出锁片 (16) 。
安装步骤
- 按照与拆卸相反的顺序安装歧管 (14) 。
- 按照交替顺序拧紧螺栓 (12) 至扭矩为 5 ± 1 N·m (44 ± 9 lb in)。 按照交替顺序再次拧紧螺栓 (12) 至扭矩为 5 ± 1 N·m (44 ± 9 lb in)。
- 将工具 (A) 涂覆到软管组件 (8) 内的 O 形密封圈上。
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Gear Group (Rear) - Remove
390F Excavator Refrigerant Compressor - Remove and Install
349F and 352F Excavators Machine System Specifications Suction Fan
349F and 352F Excavators Machine System Specifications Fuel Tank
UPS 750 Uninterruptible Power Supply System Configuration
390F Excavator Engine Front Mount - Remove and Install
2014/05/16 New Software Is Used on Certain Tier 4 Interim Industrial Engines {1901, 1902, 1920}
374F Excavator Alternate Exit
390F Excavator Water Pump - Remove and Install
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Manual Hydraulic Valve - Health Check
3500 Generator Sets with Dynamic Gas Blending Gas Filter Condensation - Drain
390F Excavator C18 Engine Supplement Turbocharger - Remove and Install
2014/02/26 An Improved Engine Oil Filter Element Is Used for Certain C175 Commercial Engines {1308}
390F Excavator Enclosure (Cooling System Package) - Remove and Install
390F Excavator Aftercooler - Remove and Install
374F Excavator Leaving the Machine
349F and 352F Excavators Machine System Specifications Pilot Lines
390F Excavator Hydraulic Oil Cooler - Remove and Install - Rear
390F Excavator Hydraulic Oil Cooler - Remove and Install - Front
374F Excavator Machine Systems BLCV and SLCV - Calibrate - If Equipped
374F Excavator Camera Harness - Disconnect and Connect
390F Excavator Radiator - Remove and Install - Front
Required Parts for Installing Turbochargers on Certain 2007 On-Highway Truck Engines {1052, 1053} Required Parts for Installing Turbochargers on Certain 2007 On-Highway Truck Engines {1052, 1053}
C8.7 Marine Engines Air Inlet and Exhaust System