BLCV and SLCV - Calibrate - If Equipped
简介
使用下述步骤标定动臂降下控制阀和斗杆降下控制阀。
注: 完成标定前,必须安装前部结构。
初步测试
- 测试和调整, "旋转斜盘 - 标定"
机器准备
- 将机器停放在水平地面上。 完全缩回斗杆油缸和铲斗油缸。 缩回动臂油缸,直到铲斗齿尖平放在地面上。 参考图 1。
Show/hide table
图 1 | g03345286 |
标定步骤
Show/hide table
机器突然动作,会导致人员伤亡。 机器突然移动,会对机上或机器近处的人员造成伤害。 为避免伤亡事故,开动机器之前,确保机器周围没有人及各种障碍物。 |
注: 标定步骤期间,可以移动机器。 通过释放所有操纵杆,可以中止标定。
监视器步骤
Show/hide table
下降单向阀     |
BLCV(动臂下降单向阀)     |
SLCV(斗杆下降单向阀)     |
- 起动发动机。
- 将液压油温度提高至 55°± 5°C (131°± 9°F)。 请参阅测试和调整, "液压系统预热"。
- 要执行标定,进入监视器。
- 进入 "Service(维修)"菜单。
- 输入密码 "9992"。
- 选择 "Configurations(配置)"。
- 选择 "Work Mode(工作模式)"。
- 将 "Hydraulic Power Mode(液压功率模式)"设置为 "STD(标准)"。
- 进入 Service(维修)菜单。
- 输入维修密码 "9992"。
- 选择 "Calibration(标定)"菜单。
- 选择 "Calibrations(标定)"菜单中的 "Lowering Check Valves(下降单向阀)"。 请参阅表 1 中的相应标定。
- 遵循监视器上的说明完成标定。
- 如果标定成功且没有错误发生,则显示屏将指示标定完成。
注: 如果出现错误,监视器上将显示 "Error(错误)"。 标定流程将不会保存,并且流程必须重新开始。
ET 步骤
Show/hide table
ACS 阀标定     |
动臂下降单向阀     |
斗杆下降单向阀标定     |
- 起动发动机。
- 将液压油温度提高至 55°± 5°C (131°± 9°F)。 请参阅测试和调整, "液压系统预热"。
- 选择"机器控制装置"的 ECM。
- 从 "Service(维修)"菜单中选择 "Calibrations(标定)"。
- 选择要完成的相应标定。 参考表 2。
- 选择 "Start(开始)"。
- 遵循屏幕上的说明完成标定。
- 如果没有出现错误,则标定成功完成。
Caterpillar Information System:
390F Excavator Hydraulic Oil Cooler - Remove and Install - Front
390F Excavator Hydraulic Oil Cooler - Remove and Install - Rear
349F and 352F Excavators Machine System Specifications Pilot Lines
374F Excavator Leaving the Machine
390F Excavator Aftercooler - Remove and Install
390F Excavator Enclosure (Cooling System Package) - Remove and Install
2014/02/26 An Improved Engine Oil Filter Element Is Used for Certain C175 Commercial Engines {1308}
390F Excavator C18 Engine Supplement Manifold (DEF Heater) - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Gear Group (Rear) - Remove
390F Excavator Refrigerant Compressor - Remove and Install
349F and 352F Excavators Machine System Specifications Suction Fan
349F and 352F Excavators Machine System Specifications Fuel Tank
374F Excavator Camera Harness - Disconnect and Connect
390F Excavator Radiator - Remove and Install - Front
Required Parts for Installing Turbochargers on Certain 2007 On-Highway Truck Engines {1052, 1053} Required Parts for Installing Turbochargers on Certain 2007 On-Highway Truck Engines {1052, 1053}
C8.7 Marine Engines Air Inlet and Exhaust System
C3.4B Engines Switch Circuits - Test - Engine Oil Pressure Switch
349F and 352F Excavators Machine System Specifications Hydraulic Tank Mounting
C3.4B Engines Valve Position - Test
349F and 352F Excavators Machine System Specifications Air Conditioner Lines
390F Excavator Radiator - Remove and Install - Rear
C27 and C32 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
2014/05/30 New Rocker Arms Are Used for Certain C27 and C32 Machine Engines {1102, 1123}
C27 and C32 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install