Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
拆卸步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | - | Loctite 771 防粘结剂 | - |
- 拆下螺栓 (1) 和薄板组件 (2) 。
Show/hide table
 | |
| 图 1 | g03610059 |
- 拆下温度传感器（火焰检测） (3) 。
Show/hide table
 | |
| 图 2 | g03610078 |
- 断开线束组件 (4) 。 切断该线束组件的所有电缆扎带。
Show/hide table
 | |
| 图 3 | g03610105 |
- 拆下螺栓 (6) 和盖 (7) 。 拆下温度传感器（DPF 进口） (5) 。
Show/hide table
 | |
| 图 4 | g03610113 |
安装步骤
- 按与拆卸相反的顺序安装温度传感器（DPF 进口，火焰检测）。
注: 始终使用类似的电缆扎带更换金属电缆扎带。 切勿使用塑料电缆扎带。
注: 按原始位置布置线束组件 (4) ，防止线束组件过热。
- 将工具 (A) 涂抹到温度传感器（火焰检测） (3) 的螺纹和温度传感器（DPF 进口） (5) 的螺纹上。 将温度传感器（火焰检测） (3) 和温度传感器（DPF 进口） (5) 拧紧至扭矩为 45 ± 5 N·m (33 ± 4 lb ft)。
Caterpillar Information System:
C3.4B Engines Glow Plug Starting Aid - Test
XQ125 Generator Set Fan Clearance - Check
C4.4 Marine Generator Set Speed/Timing - Test
349F and 352F Excavators Machine System Specifications Pilot Lines
349F and 352F Excavators Machine System Specifications Fasteners
390F Excavator C18 Engine Supplement Temperature Sensor (Catalyst Inlet) - Remove and Install
390F Excavator C18 Engine Supplement Fuel Manifold (ARD) - Remove and Install
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Boom Hydraulic System - Health Check
390F Excavator C18 Engine Supplement Catalyst (SCR) - Remove and Install
DE Series Generator Sets With Cat C3.3 Engine Starting Motor - Inspect
DE Series Generator Sets With Cat C3.3 Engine Fuel System Secondary Filter - Replace
DE Series Generator Sets With Cat C3.3 Engine Fuel System Primary Filter/Water Separator - Drain
349F and 352F Excavators Machine System Specifications Track Adjuster
2014/02/26 A New Sea Water Plug and Zinc Rod Are Used On Certain C32 Marine Engines {1379}
C27 and C32 Engines for Caterpillar Built Machines Turbocharger Outlet Pressure Sensor - Remove and Install
C175-16 Petroleum Generator Set Engines Centrifugal Oil Filter - Clean
The Hydraulic Tank Baffle is Failing on Certain Off-Highway Trucks{5056} The Hydraulic Tank Baffle is Failing on Certain Off-Highway Trucks{5056}
349F and 352F Excavators Machine System Specifications Boom Cylinder Lines
C4.4 Marine Generator Set Sensor Calibration Required - Test
C4.4 Marine Generator Set Aftercooler - Assemble - Air - to - Air Charge Cooler
C4.4 Marine Generator Set Aftercooler - Disassemble - Air - to - Air Charge Cooler
C4.4 Marine Generator Set Aftercooler - Assemble - Keel-cooled
C4.4 Marine Generator Set Aftercooler - Disassemble - Keel-cooled
C4.4 Marine Generator Set Aftercooler - Remove and Install - Keel-Cooled