Hydraulic System Warm-Up
简介
使用下述步骤将液压油预热至 55° ± 5°C (131° ± 9°F)。
请参阅操作和保养手册, "发动机和机器预热",了解冷起动机器的更多信息。
预热步骤
- 起动发动机。
- 使用监视器将自动预热目标温度更改为 55° C (131° F)。
- 进入 "Service(维修)"菜单。
- 输入密码 "9992"。
- 选择 "Configurations(配置)"。
- 选择 "Machine Attachments(机器附件)"。
- 选择 "Auto Hyd Warm Up Temp(自动液压预热温度)"。
- 输入 55° C (131° F)。
Show/hide table
图 1 | g03689765 |
(1) "机器附件" (2) "自动液压预热温度" (3) 主菜单键 |
- 按下监视器上的归位键 (3) 。
- 将机具置于地面。
- 将液压启用操纵杆置于 LOCKED(锁定)位置。
- 按下监视器上的自动预热键 (5) 。
注: 监视器上将显示一条消息,以将机具置于地面。
Show/hide table
图 2 | g03689767 |
(4) 开始自动预热? (5) 自动预热键 |
- 再次按下自动预热键 (5) 以启动自动预热功能。
- 将自动液压预热温度复位到原来的设置。
Show/hide table
图 3 | g03689770 |
(6) 自动预热启动 |
注: 当自动预热功能激活时,监视器上将显示 "Auto Warming Up Starting(自动预热启动)"消息。
注: 液压油温度达到 55° C (131° F) 后,或液压启用操纵杆移到 UNLOCKED(解锁)位置时,自动预热将停止。
Caterpillar Information System:
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Alarm - Test
C15 and C18 On-Highway Engines Exhaust Sensor Lines - Remove and Install - Exhaust Gas Venturi
Procedure to Return the Fuel Filter for Certain Caterpillar Equipment{1260, 1261, 1274} Procedure to Return the Fuel Filter for Certain Caterpillar Equipment{1260, 1261, 1274}
2013/10/21 Improved Case Assembly is Used on Certain CX31-P600 Petroleum Transmissions {3064}
C4.4 Engines for Caterpillar Built Machines Crankshaft - Spheroidal Graphite Iron (SGI) Crankshaft
440-0842 Major Engine Overhaul Foundational Kit for 3512 Engines{1000} 440-0842 Major Engine Overhaul Foundational Kit for 3512 Engines{1000}
C7.1 Industrial Engine Turbocharger Exhaust Temperature Sensor
2013/09/24 A New Ether Cylinder O-ring is Now Used on All Caterpillar Products {1456}
2013/10/31 A New Pump Bracket is Now Used on Certain C12 Marine Engines Equipped with a Bronze Impeller Pump {1371}
2013/10/28 New Engine Software Is Used for Certain C280 Marine Engines {1901, 1920}
349F and 352F Excavators Machine System Specifications Fan Drive Pump
Lubrication Requirements for the 244-1224 Fan Shaft Assembly on Certain 3500 Engines{1353, 1356} Lubrication Requirements for the 244-1224 Fan Shaft Assembly on Certain 3500 Engines{1353, 1356}
440-0928 Major Engine Overhaul Foundational Kit for 3512C Engines{1000} 440-0928 Major Engine Overhaul Foundational Kit for 3512C Engines{1000}
C15 and C18 On-Highway Engines Nozzle Heater Harness - Remove and Install
C9 Engine Maintenance Interval Schedule
374F Excavator Counterweight Removal and Installation
PM820, PM822, and PM825 Cold Planer Rotor Drive Belt - Inspect
CX31-P600 Petroleum Transmission Transmission Warm-up
2013/12/23 New Exhaust Shield Assemblies Are Used on Certain 3408 and 3412 Engines {1107}
131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709} 131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709}
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Connector Contact Description
PM820, PM822, and PM825 Cold Planer Rotor Drive (Planetary) Oil Sample - Obtain
CX31-P600 Petroleum Transmission Transmission Cooling System
2013/10/02 Improvements for Products and Systems Connected to Product Link {7606}