System Monitoring
电子控制模块(ECM)监控受控系统的工作参数。 如果特定系统参数超过监控系统所定义的可接受范围,则 ECM 将产生事件代码。 有关事件代码的信息,参考故障排除, "事件代码",以便了解针对此应用的相应事件代码列表。
每个参数可能会具有以下三种响应。 有些响应对某些参数是无效的。 参考表 1。
Show/hide table
指示灯(1)、(2)和(3)     | |
---|---|
警告类别指示灯     | 严重程度     |
(1)     | 最低严重程度     |
(2)     | 中等严重程度     |
(3)     | 最高严重程度     |
使用 Caterpillar 电子技师(ET)执行监控系统的以下工作:
- 查看参数
- 参数编程
- 设置延迟时间
参数的默认设置已在出厂时进行了编程。 为了适应特定的用途和场所,可以使用 Cat ET 对某些参数重新编程。 利用 Cat ET 修改监控系统参数。
注: 有些参数不需要密码即可进行更改。 有些参数的更改需要客户密码。 有些参数受出厂密码的保护。 有些参数无法进行更改。 有些应用不允许对可编程监控系统进行任何更改。 受到出厂密码保护的参数只能由代理商的工作人员进行更改。
查看或更改监控系统的设置
使用以下步骤来查看参数设置和/或更改参数设置:
- 在 Cat ET 上选择 "Service/Monitoring System(维修/监控系统)"屏幕。
- 高亮显示所需参数。 接着点击屏幕左下角的 "Change"(更改)按钮。
此时会出现 "Change Monitor System"(更改监控系统)屏幕。
注: 在继续进行操作前,请确保为要更改的参数选择了正确的 ECM。
- 更改参数的 "State(状态)"。
- 按照屏幕下半部分显示的 "Allowed Values(容许值)"设置 "Trip Point(触发点)"和 "Delay Time(延迟时间)"。
- 点击 "OK"(确认)按钮。
如果需要密码,会出现 "Enter Passwords"(输入密码)屏幕。 输入正确的密码,然后点击 "OK"(确定)按钮。
注: 如果需要出厂密码,会出现 "Enter Factory Passwords(输入出厂密码)"屏幕。 有关获得出厂密码的信息,请参考故障诊断与排除, "出厂密码"。
新的设置会立即生效。
注: 出厂密码仅供来自授权的 Caterpillar 代理商的维修技师使用。 Caterpillar 的客户无权访问 Caterpillar 工厂密码系统(FPS)。
Caterpillar Information System:
Release Notes for VisionLink and VisionLink Store for All Caterpillar Products {7606, 7620} Release Notes for VisionLink and VisionLink Store for All Caterpillar Products {7606, 7620}
C15 and C18 Engines Welding on Engines with Electronic Controls
C1.5 and C2.2 Engines for Caterpillar Built Machines ECM Harness Connector Terminals
C175-16 Locomotive Engine Air Lines - Aftercooler
C1.5 and C2.2 Industrial Engines Idle Validation Switch Circuit - Test
C175-16 Locomotive Engine Air Lines - Aftercooler
2013/03/21 New Water Ferrules Are Available for 3500 Engine Cylinder Heads {1124, 7555}
794 AC Off-Highway Truck Engine Starting
MT4400D AC Off-Highway Truck Fire Prevention and Explosion Prevention
2012/11/19 Improved Process for Activating Product Link PL522 On Assets In China {7606}
2012/11/26 Improved Exciter Rotor Design is Now Used on Certain Caterpillar Products {4454, 4465}
C175-16 and C175-20 Engines for Caterpillar Built Machines Alternator - Remove and Install
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Fuel Actuator - Test
3512B and 3512C Petroleum Generator Set Engines Direct Fuel Control Mode - Test
CG137-08 and CG137-12 Engines Rotary Actuator (Carburetor) - Remove and Install - G3408B
CG137-08 and CG137-12 Engines Aftercooler - Remove and Install - G3408B
421-9723 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000} 421-9723 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000}
421-9725 Top End Engine Overhaul Foundational Kit for 3412E Marine Engines{1000} 421-9725 Top End Engine Overhaul Foundational Kit for 3412E Marine Engines{1000}
3516B Engine Fuel Injector - Check
G3500 A3 Engines Air/Fuel Ratio Control - Adjust - NO<SUB>X</SUB> Feedback
CG137-08 and CG137-12 Engines Turbocharger - Remove and Install - G3408B
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Fuel Shutoff - Test
2013/06/19 An Improved Air Conditioner Condenser Fan Motor is Available for Certain Excavators {1805}
3516B Engine Water Temperature Regulators - Remove