Water Temperature Regulators - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7573 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Drain the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change". Drain the cooling system until the level of the coolant is below the exhaust manifolds.
Show/hide table
Illustration 1 g03323651 - Remove tube assembly (1) and elbow (2) from the water temperature regulator housing.
Show/hide table
Illustration 2 g00602197 Typical example - Attach Tooling (A) and a suitable lifting device to water temperature regulator housing (4). Remove bolts (3). Remove water temperature regulator housing (4).
Show/hide table
Illustration 3 g00602198 - Remove water temperature regulators (5). Remove gasket (6).
Visually inspect ferrule (7) and the seals for water temperature regulators (5). Obtain new parts for assembly, if necessary.
Caterpillar Information System:
2013/06/19 An Improved Air Conditioner Condenser Fan Motor is Available for Certain Excavators {1805}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Fuel Shutoff - Test
CG137-08 and CG137-12 Engines Turbocharger - Remove and Install - G3408B
G3500 A3 Engines Air/Fuel Ratio Control - Adjust - NO<SUB>X</SUB> Feedback
3516B Engine Fuel Injector - Check
421-9725 Top End Engine Overhaul Foundational Kit for 3412E Marine Engines{1000} 421-9725 Top End Engine Overhaul Foundational Kit for 3412E Marine Engines{1000}
421-9723 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000} 421-9723 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000}
CG137-08 and CG137-12 Engines Aftercooler - Remove and Install - G3408B
CG137-08 and CG137-12 Engines Rotary Actuator (Carburetor) - Remove and Install - G3408B
3512B and 3512C Petroleum Generator Set Engines Direct Fuel Control Mode - Test
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Fuel Actuator - Test
3516C Locomotive Engines Selective Catalytic Reduction System Monitoring
3516B Engine Overhaul (Top End)
Inspection and Cleaning Procedure For Certain Uninterruptible Power Supplies{4480} Inspection and Cleaning Procedure For Certain Uninterruptible Power Supplies{4480}
C175-16 Locomotive Engine Engine Oil Pan
C1.5 and C2.2 Industrial Engines Solenoid Valve - Test
C175-16 Marine Engine Flywheel
C175-16 Marine Engine Engine Harness
C175-16 Marine Engine Engine Harness
2012/12/21 New Sequence for Adjusting the Fuel Injectors in 3516, 3516B, and 3516C Engines {1290}
TA2 Inspection for C175-16 and C175-20 Engines{1000} TA2 Inspection for C175-16 and C175-20 Engines{1000}
C175-16 Marine Engine Generator Coupling
C27 and C32 Industrial Engines Coolant (ELC) - Change
421-9726 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000} 421-9726 Top End Engine Overhaul Foundational Kit for 3412C Marine Engines{1000}