Pistons and Connecting Rods - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 6V-6192 | 钳子 | 1 |
B | 7B-7974 | 活塞环扩张器总成 | 1 |
C | 5P-8639 | 液压压力 (连杆轴承) | 1 |
8F-0024 | 软管组件 | 1 | |
1P-2375 | 连接器 | 1 | |
1P-2376 | 连接器 | 1 | |
5P-8651 | 隔套 | 1 | |
5P-8649 | 齿座 | 1 | |
5P-8650 | 衬套接头 | 1 | |
9U-6600 | 液压泵 | 1 |
注: 从发动机上拆下之前,活塞和连杆组件上已经做了标记。 所有的部件必须重新组装在一起。 所有部件必须安装回它们在发动机中原来的位置。 请勿互换任何部件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 沿着长度方向 (Y) 对连杆 (6) 进行加热。
(Y) 加热连杆的最大长度 ...
95 mm (3.7 inch) - 让连杆和轴承冷却到室温。
- 用工具 (C) 来拆掉旧轴承,同时换上新轴承 (7)。 工具 (C) 的适配器应与连杆 (6) 的表面充分接触。
注: 将轴承接头的方位调整到 (X) 位置的 ± 5 度范围内。
- 用销膛磨机加工轴承孔 (7),以修正直径。
轴承孔直径 ...
60.035 ± 0.008 mm (2.3636 ± 0.0003 inch) Show/hide table图 3 g01056145 - 将控油活塞环的弹簧安置在活塞组件的油环槽中。
- 将控油活塞环 (3) 安置在弹簧上方。 放好控油活塞环,让开口与弹簧连接处相距 180 度。 使用工具 (B) 将控油活塞环安装到活塞上。
- 使用工具 (B) 安装中间活塞环 (2),使有 “UP-2” 标记的一侧朝向活塞顶部。
- 使用工具 (B) 安装顶部活塞环 (1),使有 “UP-1” 标记的一侧朝向活塞顶部。
- 安置活塞环 (1)、 (2) 和 (3),使其开口之间互成120度。
- 检查活塞环 (1)、 (2) 和 (3) 底部之间的间隙。 请参考技术规格, "活塞和活塞环"。
- 将活塞体组件 (4) 放置到连杆 (6) 上。 将清洁的发动机机油涂覆到连杆销 (8) 上,然后安装连杆销。 使用工具 (A) 安装销固定器 (5)。
- 将上连杆轴承 (9) 安装到连杆 (6) 中。
注: 确保轴承锁舌位于连杆的槽口中。
- 将连杆轴承下轴瓦 (10) 安装到连杆轴承盖 (11) 中。
注: 确保轴承锁舌位于连杆轴承盖的槽口中。
- 确保连杆轴承盖中已安装了定位销。
Show/hide table
图 1 | g01017742 |
Show/hide table
图 2 | g01018268 |
Show/hide table
注意 |
---|
在安装活塞销子轴承的时候,必须对连杆进行加热处理。 不要使用明火加热。 |
结束:
- 安装活塞和连杆。 请参阅拆解和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
C32 Marine Engines Pistons and Connecting Rods - Disassemble
C32 Marine Engines Pistons and Connecting Rods - Install
C175-16 Generator Set Engine Air Cleaner - Remove and Install
C32 Marine Engines Pistons and Connecting Rods - Remove
C32 Marine Engines Inlet and Exhaust Valves - Remove and Install
C32 Marine Engines Piston Cooling Jets - Remove and Install
C32 Marine Engines Cylinder Liner - Install
2012/10/08 Check Valves Are Now Used in the Fuel System of Certain Electric Power Generation and Industrial Engines {1250, 1261, 5067}
C32 Marine Engines Cylinder Liner - Remove
C175-16 Generator Set Engine Fuel Pump (High Pressure) - Remove and Install
2012/10/24 A New Water Temperature Regulator Is Available for Certain Commercial Engines {1355}
C175-16 Generator Set Engine Fuel Control Valve - Remove and Install - Primary
C32 Marine Engines Inlet and Exhaust Valve Guides - Remove and Install
C175-16 Generator Set Engine Turbocharger - Remove and Install
2012/10/03 A New Valve Lifter Assembly Is Used in 3500B Engines {1209}
C32 Marine Engines Engine Oil Filter Base - Remove
2012/10/30 A New Valve Lifter Assembly Is Used in 3500B and 3500C Engines {1209}
C32 Marine Engines Engine Oil Filter Base - Disassemble
2012/10/03 Importance of Proper Valve Lash Setting {1102, 1121, 1123, 1209}
2012/10/04 Importance of Proper Valve Lash Setting {1102, 1121, 1123}
C32 Marine Engines Engine Oil Filter Base - Assemble
C32 Marine Engines Engine Oil Filter Base - Install
C32 Marine Engines Engine Oil Cooler - Remove
C32 Marine Engines Engine Oil Cooler - Install