Engine Oil Filter Housings - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 和适当的起吊设备连接到机油滤清器壳体组件 (9) 上。 机油滤清器壳体组件的重量约为 680 kg (1500 lb)
- 定位机油滤清器壳体组件 (9) 后安装 21 条螺栓 (10) 。 拧紧螺栓 (10) 至扭矩为 370 ± 50 N·m (273 ± 37 lb ft)。
Show/hide table
图 1 | g03092658 |
- 安装螺栓 (7) 和螺栓 (8) 。 拧紧螺栓 (7) 和 (8) 至扭矩为 105 ± 20 N·m (77 ± 15 lb ft)。
Show/hide table
图 2 | g03093520 |
- 安装螺栓 (6) 。 拧紧螺栓 (6) 至扭矩为 47 ± 9 N·m (416 ± 80 lb in)。
Show/hide table
图 3 | g03093719 |
Show/hide table
图 4 | g03093680 |
- 安装螺栓 (4) 和螺栓 (5) 。 拧紧螺栓 (4) 和 (5) 至扭矩为 47 ± 9 N·m (416 ± 80 lb ft)。
- 安装管组件 (1) 、管组件 (2) 和管组件 (3) 。
Show/hide table
图 5 | g03093958 |
End By:
- 安装涡轮增压器。
- 安装发动机机油滤清器滤芯。
- 安装发动机机油冷却器。
Caterpillar Information System:
3516B Engine Engine Oil Level - Check
797F and 797F XQ Off-Highway Trucks Machine Systems Radiator Grill - Remove and Install
3500 Industrial Engines Engine Oil Pan
3500C Marine Engines Turbocharger Oil Lines
3516B Engine Refill Capacities
3516B Engine Plate Locations and Film Locations
797F and 797F XQ Off-Highway Trucks Machine Systems Engine Shutdown Switch and Disconnect Switch - Remove and Install
3516B Engine Product Description
2014/03/07 New Exhaust Elbows and Bellows Are Used for the Turbine Inlets on Certain G3516B and G3520B Engines {1052, 1059}
C7.1 Industrial Engine Turbocharger - Inspect
797F and 797F XQ Off-Highway Trucks Machine Systems Hood (Rear) - Remove and Install
797F and 797F XQ Off-Highway Trucks Machine Systems Hood (Front) - Remove and Install
3500B Engines for Caterpillar Built Power Modules Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
3500B Engines for Caterpillar Built Power Modules Engine Oil Filter
3512B and 3512C Petroleum Generator Set Engines Crankcase Breather
C7.1 Engines Clean Emissions Module Has High Oxygen Level
C7.1 Industrial Engine Walk-Around Inspection
2012/10/11 New Clamp for Fuel Injection Lines on C6.6 Machine Engines {1251, 1290, 7553}
3500 Generator Set Engines Engine Oil Lines
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215} Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
3500C Marine Engines Fan Drive
C7.1 Industrial Engine Reference Material
C18 Generator set and C18 Marine Engines Auxiliary Water Pump - Disassemble - Type 2
C18 Generator set and C18 Marine Engines Auxiliary Water Pump - Assemble - Type 2