Exhaust Manifold
Show/hide table
Illustration 1 | g03022437 |
Show/hide table
Specification for 363-1957 Exhaust Manifold Gp | |||
Item | Qty | Part | Specification Description |
- | - | - | Seal ring groove should not break into air passage at corners. |
1 | 14 | 304-9595 Bellows As | Ensure that bellows are installed for proper flow direction as indicated on bellows by arrow. |
2 | 28 | 239-6808 Clamp | Before assembly, lubricate the threads, bearing surfaces and the inside diameter of the clamps with Loctite C5A Copper Anti-Seize. |
Torque to |
|||
3 | 64 | 9L-7373 High Temperature Bolt | Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize. |
Show/hide table
Illustration 2 | g03022436 |
Detail of area A |
Show/hide table
Specification for 363-1957 Exhaust Manifold Gp | |||
Item | Qty | Part | Specification Description |
4 | 12 | 1C-2251 Bolt | Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize. |
5 | 4 | 5M-1719 Taperlock Stud | Torque to |
6 | 8 | 1D-4595 Bolt | Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize. |
7 | 4 | 9L-2295 High Temperature Bolt | Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize. |
Torque to |
|||
8 | 2 | 364-5416 Bellows As | Ensure that bellows are installed for proper flow direction as indicated on bellows by arrow. |
9 | 4 | 243-2975 Clamp As | Before assembly, lubricate the threads, bearing surfaces and the inside diameter of the clamp assemblies with Loctite C5A Copper Anti-Seize. |
Torque to |
|||
10 | 4 | 241-2634 Clamp As | Before assembly, lubricate the threads, bearing surfaces and the inside diameter of the clamp assemblies with Loctite C5A Copper Anti-Seize. |
Torque to |
|||
11 | 2 | 263-1174 Band Clamp | Before assembly, lubricate the threads, bearing surfaces and the inside diameter of the band clamps with Loctite C5A Copper Anti-Seize. |
Torque to |
|||
12 | 4 | 7L-6443 High Temperature Bolt | Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize. |
13 | 12 | 9L-2295 High Temperature Bolt | Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize. |
Caterpillar Information System:
CX48-P2300 Petroleum Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Remove and Install
3500C Marine Engines Stub Shaft (Front)
3500C Marine Engines Stub Shaft (Front)
3512B and 3512C Petroleum Generator Set Engines Exhaust Fitting
3512C and 3516C Marine Engines Exhaust Manifold
3512C and 3516C Marine Engines Fuel Injector
G3500 Engines Gear Group (Rear)
3512C and 3516C Marine Engines Exhaust Manifold
3512C and 3516C Marine Engines Engine Trunnion
3512C and 3516C Marine Engines Exhaust Bypass Valve
3512C and 3516C Marine Engines Exhaust Bypass Valve
C7.1 Industrial Engine Safety Messages
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System System Schematic
Procedure for Checking Ash Build-Up Within the Diesel Particulate Filter (DPF) {108F} Procedure for Checking Ash Build-Up Within the Diesel Particulate Filter (DPF) {108F}
2012/08/28 A New Power Distribution Box and Disconnect Switch Is Used on C175-16 Generator Set Engines {1417, 1420, 4461}
C175-16 Locomotive Engines Safety Messages
C175-16 Engine Emergency Stopping
C175-16 Engine Fuel Tank Water and Sediment - Drain
C175-16 Engine Aftercooler Core - Inspect/Clean
2012/05/02 New Transmission Software is Available for Certain CX31 Transmissions and Certain CT660 On-Highway Trucks {7620}
WAVS Generic Installation Guide for Certain Cat® Products{7347, 7348} WAVS Generic Installation Guide for Certain Cat® Products{7347, 7348}
G3500 Engines Camshaft Bearing Position
3500C Marine Engines Cylinder Block
3512C and 3516C Marine Engines Air Cleaner