Fuel Tank Water and Sediment - Drain
Show/hide table
| 注意 |
|---|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 有关适于收集和盛放 Cat 产品油液的工具和用品，请参阅专门出版物, NENG2500, "Cat 代理商维修工具目录"或专门出版物, PECJ0003, "Cat 车间用品和工具目录"。 按照本地法规和要求处置所有油液。 |
Show/hide table
 | |
| 图 1 | g01157156 |
Cat C175 柴油发动机的典型油水分离器 (1) 油杯 (2) 排放 | |
应该每天检查分离杯 (1) 是否有水存在。 如果油水分离器杯中有水的话，把水放掉。
- 打开排放阀 (2) 。 该放水阀是自行通风式的放水阀。 用适当的容器盛接放掉的水。 妥善处置放掉的水。
- 关闭排放阀。
Show/hide table
| 注意 |
|---|
油水分离器在发动机正常运行时处于负压状态。 确保排放口被牢固拧紧以便防止空气进入燃油系统中。 |
Caterpillar Information System:
C175-16 Engine Emergency Stopping
C175-16 Locomotive Engines Safety Messages
2012/08/28 A New Power Distribution Box and Disconnect Switch Is Used on C175-16 Generator Set Engines {1417, 1420, 4461}
Procedure for Checking Ash Build-Up Within the Diesel Particulate Filter (DPF) {108F} Procedure for Checking Ash Build-Up Within the Diesel Particulate Filter (DPF) {108F}
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System System Schematic
3512C and 3516C Marine Engines Exhaust Manifold
CX48-P2300 Petroleum Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Remove and Install
3500C Marine Engines Stub Shaft (Front)
3500C Marine Engines Stub Shaft (Front)
3512B and 3512C Petroleum Generator Set Engines Exhaust Fitting
3512C and 3516C Marine Engines Exhaust Manifold
3512C and 3516C Marine Engines Fuel Injector
C175-16 Engine Aftercooler Core - Inspect/Clean
2012/05/02 New Transmission Software is Available for Certain CX31 Transmissions and Certain CT660 On-Highway Trucks {7620}
WAVS Generic Installation Guide for Certain Cat® Products{7347, 7348} WAVS Generic Installation Guide for Certain Cat® Products{7347, 7348}
G3500 Engines Camshaft Bearing Position
3500C Marine Engines Cylinder Block
3512C and 3516C Marine Engines Air Cleaner
G3516C and G3516E Gas Engines Gear Group (Front)
3512C and 3516C Marine Engines Air Cleaner
3512C and 3516C Marine Engines Exhaust Bypass Valve
3500C Marine Engines Alternator Mounting
G3500 Engines Gear Group (Front)
2012/05/14 New Commissioning Instructions Now Used to Ensure Correct Voltage Applied to Contactor on 3406C, C15, C18, and C9 Gen Sets {1435, 7332, 7400}