3512C and 3516C Marine Engines Caterpillar

Exhaust Manifold

Usage:

3516C HZS

Show/hide table




Illustration 1	g03020116

Show/hide table

Table 1
Specification for 363-1955 Exhaust Manifold Gp
Item	Qty	Part	Specification Description
-	-	-	Seal ring groove should not break into air passage at corners.
1	4	9L-2295 High Temperature Bolt	Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize.
1	4	9L-2295 High Temperature Bolt	Torque to 55 ± 5 N·m (41 ± 4 lb ft).
2	4	241-2634 Clamp As	Before assembly, lubricate the threads, bearing surfaces and the inside diameter of clamp assemblies with Loctite C5A Copper Anti-Seize.
2	4	241-2634 Clamp As	Torque to 12 ± 1 N·m (106 ± 9 lb in).
3	4	302-5889 Band Clamp	Before assembly, lubricate the threads, bearing surfaces and the inside diameter of band clamps with Loctite C5A Copper Anti-Seize.
3	4	302-5889 Band Clamp	Torque to 12 ± 1 N·m (106 ± 9 lb in).
4	8	9H-8260 Bolt	Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize.
5	10	304-9595 Bellows As	Ensure that bellows are installed for proper flow direction as indicated on bellows by arrow.
6	20	239-6808 Clamp	Before assembly, lubricate the threads, bearing surfaces and the inside diameter of clamps with Loctite C5A Copper Anti-Seize.
6	20	239-6808 Clamp	Torque to 12 ± 1 N·m (106 ± 9 lb in).
7	1	345-0878 Bellows As	Ensure that bellows are installed for proper flow direction as indicated on bellows by arrow.
8	1	348-9252 Bellows As	Ensure that bellows are installed for proper flow direction as indicated on bellows by arrow.
9	48	9L-7373 High Temperature Bolt	Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize.

Show/hide table




Illustration 2	g03020057

Show/hide table

Table 2
Specification for 363-1955 Exhaust Manifold Gp
Item	Qty	Part	Specification Description
10	4	5M-1719 Taperlock Stud	Torque to 35 ± 5 N·m (26 ± 4 lb ft).
11	2	311-9236 Band Clamp	Before assembly, lubricate the threads, bearing surfaces and the inside diameter of band clamps with Loctite C5A Copper Anti-Seize.
11	2	311-9236 Band Clamp	Torque to 20 ± 2 N·m (177 ± 18 lb in).
12	4	7L-6443 High Temperature Bolt	Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize.
13	12	9L-2295 High Temperature Bolt	Before assembly, lubricate the threads and bearing surfaces with Loctite C5A Copper Anti-Seize.

Caterpillar Information System:

3512C and 3516C Marine Engines Fuel Injector

G3500 Engines Gear Group (Rear)

3512C and 3516C Marine Engines Exhaust Manifold

3512C and 3516C Marine Engines Engine Trunnion

3512C and 3516C Marine Engines Exhaust Bypass Valve

3512C and 3516C Marine Engines Exhaust Bypass Valve

C7.1 Industrial Engine Safety Messages

3512C and 3516C Marine Engines Exhaust Manifold

3512C and 3516C Marine Engines Exhaust Manifold

3500B and 3500C Marine Engines Connecting Rod

3500C Marine Engines Exhaust Bypass Valve

3500C Marine Engines Gear Group (Rear)

3512B and 3512C Petroleum Generator Set Engines Exhaust Fitting

3500C Marine Engines Stub Shaft (Front)

3500C Marine Engines Stub Shaft (Front)

CX48-P2300 Petroleum Transmission Lockup Clutch and Solenoid Valve (Torque Converter) - Remove and Install

3512C and 3516C Marine Engines Exhaust Manifold

CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System System Schematic

Procedure for Checking Ash Build-Up Within the Diesel Particulate Filter (DPF) {108F} Procedure for Checking Ash Build-Up Within the Diesel Particulate Filter (DPF) {108F}

2012/08/28 A New Power Distribution Box and Disconnect Switch Is Used on C175-16 Generator Set Engines {1417, 1420, 4461}

C175-16 Locomotive Engines Safety Messages

C175-16 Engine Emergency Stopping

C175-16 Engine Fuel Tank Water and Sediment - Drain

C175-16 Engine Aftercooler Core - Inspect/Clean