Fuel Manifold (ARD) - Disassemble
Disassembly Procedure
Start By:
- Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Control Manifold (ARD) - Remove".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove tube assembly (1) .
Show/hide table
Illustration 1 | g01265718 |
- Remove nut (2), washer (2), coil assembly (4), and valve assembly (5). Remove O-ring seals (6) from valve assembly (5) .
Show/hide table
Illustration 2 | g01265721 |
- Remove nut (7), washer (8), coil assembly (9), and valve assembly (10). Remove O-ring seals (11) from valve assembly (10). Repeat for the remaining solenoid valve.
Show/hide table
Illustration 3 | g01265722 |
- Remove check valve (12). Remove O-ring seals (13) from check valve (12) .
Show/hide table
Illustration 4 | g01265739 |
- Remove check valve (14). Remove O-ring seals (15) from check valve (14) .
Show/hide table
Illustration 5 | g01265741 |
Caterpillar Information System:
3512B and 3512C Petroleum Generator Set Engines Engine Cranks but Does Not Start
C175-16 Marine Engine Valve Mechanism Cover
CX48-P2300 Petroleum Transmission Control Manifold - Remove and Install
3516B Generator Set Engines with Dynamic Gas Blending ECM Does Not Communicate with Other Modules
3512B and 3512C Petroleum Generator Set Engines Cylinder Is Noisy
C175-16 Marine Engine Vibration Damper
C175-16 Marine Engine Fuel and Auxiliary Water Pump Drive
2012/06/08 Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
2012/02/20 New Torque Specification for Position Sensor on 3054E, C6.6, and C4.4 Engines {1408, 1907}
C7.1 (Mech) Industrial Engine Air Compressor - Remove and Install
2012/04/12 A New Service Replacement Front Housing Is Available for C175-16 Engines {1151, 1162, 1206}
C175-16 Marine Propulsion Engines Sensor Signal (Analog, Passive) - Test
C7 On-Highway Engine Fuel Manifold (ARD) - Assemble
C175-16 Marine Engine Engine Oil Pan
CX48-P2300 Petroleum Transmission Transmission and Torque Converter - Separate
2013/04/10 A New Spark Plug Is Used in Certain G3500 and G3600 Engines {1550, 7519}
3512B and 3512C Petroleum Generator Set Engines Engine Does Not Crank
2012/05/09 A New Cylinder Block and Flywheel Housing Are Used for C175-16 Engines {1157, 1201}
C175-16 Marine Propulsion Engines Sensor Signal (PWM) - Test
3512B and 3512C Petroleum Generator Set Engines Engine Has Early Wear
C175-16 Marine Propulsion Engines Sensor Supply - Test
3512B and 3512C Petroleum Generator Set Engines Engine Has Mechanical Noise (Knock)
CX48-P2300 Petroleum Transmission Pump Drive - Remove
CX48-P2300 Petroleum Transmission Gear Pump (Torque Converter and Transmission) - Remove and Install