Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting
Show/hide table
| 从发动机的飞轮端观看发动机，其旋向为逆时针方向（标准） | ||||
| 可进行相应的检查/调整的气缸 | ||||
| 发动机 | 1 号活塞位于上死点位置的正确冲程。 (1) | 进气门 | 排气门 | 喷油器 |
| 3516 | 压缩 | 1-2-5-7-8-12-13-14 | 1-2-3-4-5-6-8-9 | 3-4-6-9-10-11-15-16 |
| 排气 | 3-4-6-9-10-11-15-16 | 7-10-11-12-13-14-15-16 | 1-2-5-7-8-12-13-14 | |
Show/hide table
| ( 1 ) | 将 1 号活塞置于上止点 (TC) 位置，确定正确冲程。 请参阅测试与调整, "确定 1 号活塞上止点位置"。 确定针对某一冲程的上止点位置，并进行对应于此冲程的正确的气缸的相应调整。 拆下正时螺栓。 沿发动机正常旋转方向将飞轮转动 360 度。 这样就会将 1 号活塞置于与其另外一个冲程对应的上止点位置。 将正时螺栓安装到飞轮中，然后完成针对其余气缸的调整。 |
Show/hide table
| 从发动机的飞轮端观看发动机，其旋向为顺时针方向（反转） | ||||
| 需要进行检查/调整的气缸 | ||||
| 发动机 | 1 号活塞位于上死点位置的正确冲程。 (1) | 进气门 | 排气门 | 喷油器 |
| 3516 | 压缩 | 1-2-5-6-7-8-13-14 | 1-2-3-4-5-6-9-10 | 3-4-9-10-11-12-15-16 |
| 排气 | 3-4-9-10-11-12-15-16 | 7-8-11-12-13-14-15-16 | 1-2-5-6-7-8-13-14 | |
Show/hide table
| ( 1 ) | 将 1 号活塞置于上止点 (TC) 位置，确定正确冲程。 请参阅测试与调整, "确定 1 号活塞上止点位置"。 确定针对某一冲程的上止点位置，并进行对应于此冲程的正确的气缸的相应调整。 拆下正时螺栓。 沿发动机正常旋转方向将飞轮转动 360 度。 这样就会将 1 号活塞置于与其另外一个冲程对应的上止点位置。 将正时螺栓安装到飞轮中，然后完成针对其余气缸的调整。 |
Caterpillar Information System:
C175-16 and C175-20 Generator Set Engines Fuel Temperature Is High - Sensor is Located at the Fuel Manifold
PL87 Pipelayer Machine Systems Alternator
2012/09/11 Generator Maintenance and Protective Relays Benefit the Service Life of Generator on Certain Cat® Products {4450}
2011/12/15 New Software Is Now Available for Product Link (PL 121) {7602, 7610, 7620}
C175-16 and C175-20 Generator Set Engines Fuel Temperature Is High - Sensor is Located at the Fuel Filter Base
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Measuring Inlet Manifold Pressure
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Engine Governing - Adjust
3516C Generator Set Engines Lubrication System Operation
924K, 930K and 938K Wheel Loaders Electrohydraulic System Check Valve (Secondary Steering)
C13 Generator Set Generator Lead Connections
826K Landfill Compactor Selective Catalytic Reduction Warning System
3516C Generator Set Engines Aftertreatment Identification Module - Test
D Series Excavator Monitoring System Configuration Mode
2011/12/19 Use the FT3193 Harness Assembly to Communicate with the Adem II 6X/6U ECM on Certain Truck Engines {1408, 1901}
2011/12/19 Use the FT3193 Harness Assembly to Communicate with the Adem II 6X/6U ECM on Certain Industrial Engines {1408, 1901}
2011/12/22 A New O-ring and Oil Pan Drain Plug Are Now Used on Certain C12 Marine Engines {1302, 7553, 7555}
2014/07/07 An Improved Guide Spring and Valve Lifter Assembly Are Used in Certain C-9, C9 ACERT Engines, and C9.3 ACERT Engines {1108}
2011/12/15 Procedure to Remedy Loose V-belts on Certain C18 and C32 Marine Engines {1207, 1358, 1359, 1397}
2012/03/02 Improved Turbocharger Oil Drain Tubes Are Used on Certain C18 and 3406E Commercial Engines {1052, 1307}
Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286} Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286}
G3500 Generator Sets Maintenance Interval Schedule - Prime
C175-16 and C175-20 Generator Set Engines Fuel Rail Temperature Is High
C9.3 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C9.3 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install