Alternator
Show/hide table
图 1 | g02539616 |
Show/hide table
197-8820 充电交流发电机总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
用碳堆式 4C-4911 蓄电池负载测试仪 加载蓄电池以达到最大交流发电机输出。     | |||
1     | 1     | 2K-4821 锁紧螺母     | 拧紧至扭矩为 127 ± 10 N·m (94 ± 7 lb ft)。     |
2     | 1     | 5S-7349 螺栓     | (B-) 接线端。 拧紧至扭矩为 4.4 ± 1.0 N·m (38.9 ± 8.9 lb in)。     |
3     | -     | -     | (R) 接线端为来自定子的交流输出,不可用于诊断。     |
4     | 1     | 6V-8189 螺母     | 对于 (B+) 接线端,使用 7/16 环形端子。     |
(B+) 接线端。 拧紧至扭矩为 18.2 ± 2.4 N·m (161.1 ± 21.2 lb in)。 |
|||
-     | -     | -     | 电流为 95 安培。     |
-     | -     | -     | 极性为负极接地。     |
-     | -     | -     | 旋转方向为顺时针方向。     |
-     | -     | -     | 5000 rpm 时的最小满载电流为 95 安培。     |
-     | -     | -     | 2000 rpm 时的最小满载电流为 28 安培。     |
-     | -     | -     | 输出电压为 28 ± 1 V。     |
Caterpillar Information System:
2012/09/11 Generator Maintenance and Protective Relays Benefit the Service Life of Generator on Certain Cat® Products {4450}
2011/12/15 New Software Is Now Available for Product Link (PL 121) {7602, 7610, 7620}
C175-16 and C175-20 Generator Set Engines Fuel Temperature Is High - Sensor is Located at the Fuel Filter Base
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Measuring Inlet Manifold Pressure
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Engine Governing - Adjust
3516C Generator Set Engines Lubrication System Operation
924K, 930K and 938K Wheel Loaders Electrohydraulic System Check Valve (Secondary Steering)
C13 Generator Set Generator Lead Connections
826K Landfill Compactor Selective Catalytic Reduction Warning System
3516C Generator Set Engines Aftertreatment Identification Module - Test
3516E Generator Set Engine 100 Hour Free Configuration on Engine Start-up
3516C Generator Set Engines Data Link Configuration Status - Test
C175-16 and C175-20 Generator Set Engines Fuel Temperature Is High - Sensor is Located at the Fuel Manifold
3516C Generator Set Engines Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting
D Series Excavator Monitoring System Configuration Mode
2011/12/19 Use the FT3193 Harness Assembly to Communicate with the Adem II 6X/6U ECM on Certain Truck Engines {1408, 1901}
2011/12/19 Use the FT3193 Harness Assembly to Communicate with the Adem II 6X/6U ECM on Certain Industrial Engines {1408, 1901}
2011/12/22 A New O-ring and Oil Pan Drain Plug Are Now Used on Certain C12 Marine Engines {1302, 7553, 7555}
2014/07/07 An Improved Guide Spring and Valve Lifter Assembly Are Used in Certain C-9, C9 ACERT Engines, and C9.3 ACERT Engines {1108}
2011/12/15 Procedure to Remedy Loose V-belts on Certain C18 and C32 Marine Engines {1207, 1358, 1359, 1397}
2012/03/02 Improved Turbocharger Oil Drain Tubes Are Used on Certain C18 and 3406E Commercial Engines {1052, 1307}
Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286} Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286}
G3500 Generator Sets Maintenance Interval Schedule - Prime
C175-16 and C175-20 Generator Set Engines Fuel Rail Temperature Is High