Track
Show/hide table
| |
| Illustration 1 | g01424704 |
|
Typical example | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| - | - | - | All joints of the link assembly must have flexibility even with a measurable end play of zero. Flexibility is the ability for movement from the weight of the link assembly. |
| - | - | - | Use the following procedure to tighten the track bolts:
1. Tighten the track bolts to 2. Tighten the bolts to an additional turn angle of 120 ± 5 degrees. |
| - | - | - | The maximum assembly force for the link assembly is |
| 2 | - | - | The assembly force for the master pin is The assembly force for the master pin is |
| A | - | - | Protrusion for the master bushing is |
| B | - | - | Distance between the bolt holes is |
| C | - | - | Distance between the bolt holes is |
| D | - | - | Protrusion for each end of the standard bushing is |
| E | - | - | Protrusion at one end of the standard pin (1) is |
Show/hide table
| (1) | For 194-1910, 194-1920, 203-2201, 332-8908, 332-8915, 419-0977, 422-6106, 491-5612, 515-7160, 539-8167, 539-8169, 539-8170 and 540-0192. |
| (2) | For 337-9053, 337-9056, 337-9063, 359-3119, 359-3121, 359-3122, 397-8767, 415-5237, 456-2542, 469-0667, 521-5664, 521-5665, 521-5666, 521-5667, 524-6580, 524-6581, 524-6582, 527-8989 , 559-6447 , 569-9762 and 569-9763. |
Caterpillar Information System:
320E and 323E Excavators Machine System Specifications Bucket Cylinder
320E and 323E Excavators Machine System Specifications Bucket Cylinder
320E and 323E Excavators Machine System Specifications Stick Cylinder
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280} 370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
2012/03/13 A New Piston Is Used in Certain C18 Engines {1214, 1225}
Using the 217-0114 Adapter Cable As {0709, 1901, 1920} Using the 217-0114 Adapter Cable As {0709, 1901, 1920}
2011/12/05 New Heat Exchanger Groups and Spacers Are Used on Certain C18 Commercial and Marine Engines {1379}
2011/11/11 New Heat Exchanger Groups and Spacers Are Used on Certain C32 Marine Engines {1379}
320E and 323E Excavators Machine System Specifications Swivel
320E and 323E Excavators Machine System Specifications Travel Motor Guard
2011/12/14 A New Engine Oil Cooler Bypass Is Used for C175-16 Engines {1307}
2011/10/19 Improved Bolts and Washers Along with a New Procedure Are Used to Fasten the Pilot to the Lockup Clutch Housing {3101, 7553}
320E and 323E Excavators Machine System Specifications Relief Valve (Boom Lowering Control Device)
2011/10/20 New Firmware Is Now Available for Communications Adapter 3 {7610, 7620}
349F and 352F Excavators Machine System Specifications Hoist Solenoid Valve - Boom/Stick Regeneration
Modifying the Control Panel Remote Start Circuit Wiring of the Crank Rest Time Delay Relay That is used on C280 Marine Engines{1408, 1453, 7451} Modifying the Control Panel Remote Start Circuit Wiring of the Crank Rest Time Delay Relay That is used on C280 Marine Engines{1408, 1453, 7451}
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Pressure Sensor (Implement Pilot Oil)
Customer Connections for G3304B and G3306B Engines {1408, 5258} Customer Connections for G3304B and G3306B Engines {1408, 5258}
2012/01/03 Improvements Have Been Made to Manufacturing Processes of the Piston for the Track Adjuster on Certain Excavators and Mobile Hydraulic Power Units {4157}
2011/10/20 Special Instruction, REHS7410, "Customer Connections for G3304B and G3306B Engines" Is Available {1408, 5258}
3512C and 3516C Marine Auxiliary and Generator Set Engines Engine Air Cleaner Element (Single Element) - Inspect/Replace
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Guidance Terms
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Machine Dimensions
320D and 323D Excavators Machine System Specifications Stick Lines - Quick Coupler