320E and 323E Excavators Machine System Specifications Caterpillar

Stick Cylinder

Usage:

320E AWS

Show/hide table




Illustration 1	g02730787

Show/hide table

Table 1
Specification for 341-2802 Stick Cylinder and Seal Gp and 341-2807 Stick Cylinder and Seal Gp
Item	Qty	Part	Specification Description
1	1	240-2914 Bushing	Inside diameter before assembly is 80.20 ± 0.04 mm (3.157 ± 0.002 inch). Installation depth is 10 mm (0.4 inch).
2	12	4I-3628 Bolt	Torque to 367 ± 55 N·m (271 ± 41 lb ft).
A	1	352-1098 Stick Cylinder As	Bore diameter is 140 mm (5.5 inch).
B	1	352-1104 Rod As	Diameter is 100 mm (3.9 inch).
3	2	357-5711 Bushing	During press fit, insert the bushing on the side of the housing with the taper. Inside diameter before assembly is 80.32 ± 0.03 mm (3.162 ± 0.001 inch). Installation depth is 10 mm (0.4 inch).
4	1	3B-8489 Grease Fitting	Torque to 9.32 ± 0.49 N·m (82.49 ± 4.34 lb in).
5	1	096-5625 Bushing	Outside diameter before assembly is 105 mm (4.1 inch). Thickness is 2.47 mm (0.097 inch).
6	1	247-8873 Piston	Torque to 8890 ± 440 N·m (6557 ± 325 lb ft).
7	1	096-6210 Socket Setscrew	Torque to 56.9 ± 10.7 N·m (42.0 ± 7.9 lb ft). After tightening the socket setscrew, stake the socket setscrew in two places.

Caterpillar Information System:

370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280} 370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}

2012/03/13 A New Piston Is Used in Certain C18 Engines {1214, 1225}

Using the 217-0114 Adapter Cable As {0709, 1901, 1920} Using the 217-0114 Adapter Cable As {0709, 1901, 1920}

2011/12/05 New Heat Exchanger Groups and Spacers Are Used on Certain C18 Commercial and Marine Engines {1379}

2011/11/11 New Heat Exchanger Groups and Spacers Are Used on Certain C32 Marine Engines {1379}

320E and 323E Excavators Machine System Specifications Swivel

320E and 323E Excavators Machine System Specifications Travel Motor Guard

2011/12/14 A New Engine Oil Cooler Bypass Is Used for C175-16 Engines {1307}

2011/10/19 Improved Bolts and Washers Along with a New Procedure Are Used to Fasten the Pilot to the Lockup Clutch Housing {3101, 7553}

3516C Marine Engine Engine Operation

2011/12/23 Special Instruction, REHS7409, "Initial Start-Up of CG137 and G3300B Engines" Is Available {1000}

2011/11/16 A New Turbocharger Water Line Is Used for Certain 3516B and 3516C Engines {1380}

320E and 323E Excavators Machine System Specifications Bucket Cylinder

320E and 323E Excavators Machine System Specifications Bucket Cylinder

320 GC, 320 and 323 Excavator Machine Systems Specifications Track

320E and 323E Excavators Machine System Specifications Relief Valve (Boom Lowering Control Device)

2011/10/20 New Firmware Is Now Available for Communications Adapter 3 {7610, 7620}

349F and 352F Excavators Machine System Specifications Hoist Solenoid Valve - Boom/Stick Regeneration

Modifying the Control Panel Remote Start Circuit Wiring of the Crank Rest Time Delay Relay That is used on C280 Marine Engines{1408, 1453, 7451} Modifying the Control Panel Remote Start Circuit Wiring of the Crank Rest Time Delay Relay That is used on C280 Marine Engines{1408, 1453, 7451}

824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Pressure Sensor (Implement Pilot Oil)

Customer Connections for G3304B and G3306B Engines {1408, 5258} Customer Connections for G3304B and G3306B Engines {1408, 5258}

2012/01/03 Improvements Have Been Made to Manufacturing Processes of the Piston for the Track Adjuster on Certain Excavators and Mobile Hydraulic Power Units {4157}

2011/10/20 Special Instruction, REHS7410, "Customer Connections for G3304B and G3306B Engines" Is Available {1408, 5258}

3512C and 3516C Marine Auxiliary and Generator Set Engines Engine Air Cleaner Element (Single Element) - Inspect/Replace