Glossary
Show/hide table
Illustration 1 | g02723568 |
Run-time screen icons |
The following icons are depth to grade arrow indicators that indicate direction and relative distance from the target depth:
Show/hide table
Far above grade (Indicated by an Orange arrow pointed down) |
Show/hide table
Near above grade (Indicated by a Green arrow pointed down) |
Show/hide table
On grade (Indicated by two Green arrows pointed towards each other) |
Show/hide table
Near below grade (Indicated by a Green arrow pointed up) |
Show/hide table
Far below grade (Indicated by a Blue arrow pointed up) |
The following icons are system status icons that show status of and type of benchmark that is set:
Show/hide table
No elevation reference |
Show/hide table
Depth from bench |
Show/hide table
Depth from bench - Laser referenced |
Show/hide table
No elevation reference |
Show/hide table
Depth from laser |
The following icons are Linkage Elevation Monitor (LEM) icons that provide the status of the LEM feature:
Show/hide table
Feature not enabled |
Show/hide table
Linkage elevation monitor is enabled, but no limits established. |
Show/hide table
Limits defined for both ceiling and floor. |
Show/hide table
Limits defined for floor only. |
Show/hide table
Limits defined for ceiling only. |
Show/hide table
For the cases when linkage elevation monitor is not available, an exclamation mark is added with the icon to indicate attention required. For example, a sensor is missing where system cannot calculate linkage position. |
Show/hide table
Illustration 2 | g02383197 |
Bucket icon states that show direction of bucket slope and selected bucket focus point |
Show/hide table
Main menu |
Show/hide table
Soft key cycle |
Show/hide table
Heading direction |
Show/hide table
Bench rotation angle (Optional) |
Show/hide table
Benchmark |
Show/hide table
Touchpoint |
Show/hide table
Accept laser |
Show/hide table
Set ceiling |
Show/hide table
Set floor |
The following icons are set depth/slope screen icons:
Show/hide table
Illustration 3 | g02726061 |
Set depth/slope screen |
Show/hide table
Target slope |
Show/hide table
Target slope |
Show/hide table
Target cross slope |
Show/hide table
Target cross slope |
Show/hide table
Main menu |
The main menu icon displays the followingCat Grade Control options menu icons:
Show/hide table
Bucket focus select screen |
Show/hide table
Operating modes screen |
Show/hide table
Tolerance setting screen icon |
Show/hide table
Audible tones configuration screen icon |
Show/hide table
Slope units selection screen icon |
Show/hide table
Linkage elevation monitor settings screen |
Show/hide table
Bucket dimension configuration screen - This icon initiates tilt bucket angle sensor calibration. |
Show/hide table
Work tools select screen - This icon initiates screen to edit dimensions of the selected bucket. |
Caterpillar Information System:
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Planetary - Install
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Planetary - Remove
C18 Generator Set Maintenance Interval Schedule - Standby
204-7392 (Air Motor Driven) Filter Cart {0645, 0680, 0738, 5056, 5068} 204-7392 (Air Motor Driven) Filter Cart {0645, 0680, 0738, 5056, 5068}
C18 Generator Set Maintenance Interval Schedule - Prime
3516C Generator Sets Gauges and Indicators
3512E Tier 4 Final Engines for Land Electric Drilling Inlet Manifold Temperature Sensor
C13, C15, and C18 Generator Set Engines Engine Oil Temperature Sensor
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Fuel Pressure Sensor
Accumulator Discharging and Charging Procedures {0738, 4263, 4264, 4331, 5077, 5077, 5081, 7474} Accumulator Discharging and Charging Procedures {0738, 4263, 4264, 4331, 5077, 5077, 5081, 7474}
2011/11/16 An Improved Fan Assembly Is Used on Certain 3406 Generator Sets {1353, 1356}
CG137-08 and CG137-12 Generator Sets Engine Oil Lines
TH55FT-E70 and TH55FT-E90 Transmissions Power Train Electronic Control System Event Codes
3516C Generator Sets Symbols
C32 Marine Generator Set Gauges and Indicators - If Equipped
C175 Cooling System Cavitation Test {1350} C175 Cooling System Cavitation Test {1350}
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea General Information
2011/09/19 New Components and Inspection Criteria for the Oil Drain Tube Are Used for Certain 3126 and C7 Marine Engines {1052, 1307}
C32 Marine Generator Set Engine Oil Level - Check
CG137-08 and CG137-12 Generator Sets Magnetic Switch
CG137-08 and CG137-12 Generator Sets Magnetic Switch
CG137-08 and CG137-12 Generator Sets Camshaft Bearings
2011/09/19 New Hardware Components Are Used for the Oil Drain Tube on Certain C9 Marine Engines {1052, 1307}
2011/09/19 New Bolts and Spacers Are Used on the Water Manifolds of Certain Marine Engines {1380, 7553}