Auxiliary Drive (Front) - Disassemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-2321 | Combination Puller | 1 |
B | 8B-7551 | Bearing Puller | 1 |
7S-9154 | Step Plate | 1 | |
C | 1P-1863 | Retaining Ring Pliers | 1 |
D | 1P-1861 | Retaining Ring Pliers | 1 |
E | 248-3310 | Spanner Wrench | 1 |
Start By:
- Remove the auxiliary drive.
- Remove nuts (1) and the washers. Remove studs (2).
Show/hide table
Illustration 2 g02679676 - Use Tooling (A) to remove pulley (3).
Show/hide table
Illustration 3 g02679696 Show/hide tableIllustration 4 g02679717 - Loosen nut (4).
- Use a press and Tooling (B) to loosen gear (5) from the shaft.
- Remove nut (4) and remove gear (5).
Show/hide table
Illustration 5 g02679777 - Use Tooling (C) to remove retaining ring (6). Remove bearing (7) from gear (5).
Show/hide table
Illustration 6 g02679882 - Remove O-ring seal (10). Use Tooling (D) to remove retaining ring (8). Remove shaft (9).
Show/hide table
Illustration 7 g02680020 - Use Tooling (E) to remove locknut (11). Remove lockwasher (12) and remove bearing (13).
Show/hide table
Illustration 8 g02680056 - Remove lip seal (14). Note the orientation of the lip seal for installation purposes.
Show/hide table
Illustration 1 | g02679656 |
Caterpillar Information System:
3516C Generator Set Engines Sensor Signal (PWM) - Test
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Remove and Install
Retrofitting for Ultra Lean Burn (ULB) on a G3512 Engine{1000, 775E} Retrofitting for Ultra Lean Burn (ULB) on a G3512 Engine{1000, 775E}
C3.4B Engines For Caterpillar Built Machines Electronic Control Module
C13, C15, and C18 Tier 4 Final Engines Engine Oil Filter Base
C9.3 Tier 4 Final Engines Engine Oil Filter Base
C4.4 Marine Generator Set Emergency Stopping
TA19 M4WD Agricultural Transmission Transmission System
TA19 M4WD Agricultural Transmission General Information
Retrofitting a Cat 270 Air Compressor with a BA-921 CR Air Compressor on Certain C13 and C15 On-Highway Engines{1803} Retrofitting a Cat 270 Air Compressor with a BA-921 CR Air Compressor on Certain C13 and C15 On-Highway Engines{1803}
2011/08/04 Correction to Troubleshooting, SENR6493 , "3512 Engine Oil Well Service" {1265, 1901}
3516C Generator Set Engines Sensor Signal (Analog, Passive) - Test
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Assemble
CG137-08 and CG137-12 Industrial Engines Sensor Signal (Analog, Active) - Test
Checking the High-Pressure Relief Valve for Leakage on C6.6 and C4.4 Engines{1288} Checking the High-Pressure Relief Valve for Leakage on C6.6 and C4.4 Engines{1288}
TA19 M4WD Agricultural Transmission Location of Electronic Components for Transmission System
2013/08/21 A New Oversized Cylinder Bore Liner Seal Insert Is Available for 3500 Engine Cylinder Block Salvage {1201, 7555}
3516C Generator Set Engines Sensor Supply - Test
C27 Generator Set Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.3/4.4
C9.3 Engines for Caterpillar Built Machines Water Lines
C13, C15, and C18 Tier 4 Final Engines Water Pump
TA19 M4WD Agricultural Transmission Location of Hydraulic Components for Transmission System
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Regulatory Information (Japan)
C15 Generator Set Refill Capacities