A New Oversized Cylinder Bore Liner Seal Insert Is Available for 3500 Engine Cylinder Block Salvage {1201, 7555}
- Caterpillar Products:
- 3500 Family Generator Sets and Power Modules
- 3500C Engines
- G3500 Family Generator Sets and Power Modules
- Engine: Commercial
- 3500 and 3500B
- G3500 Family
The new 335-8971 Insert with a 0.254 mm (0.010 inch) oversized outer diameter is now available.
The new 335-8971 Insert has the same thickness as the 353-5618 Insert, but the new insert provides an oversized outer diameter.
The new 335-8971 Insert is intended for use as needed in replacing loose standard-sized inserts.
Show/hide table
Illustration 1 | g02649139 |
Dimensions for the insert (N) Outside diameter (P) Thickness of the insert (R) Wall thickness of the insert (S) Radius on insert |
Show/hide table
Dimensions for the Liner Seat Insert     | ||||
Part Number     | Outside Diameter (N) (4)     | Thickness of the Insert (P)     | Wall Thickness of the Insert (R)     | Radius (S)     |
353-5617 120-4334 (1) (2)     |
212.115 ± 0.013 mm (8.3510 ± 0.0005 inch)     |
5.080 ± 0.025 mm (0.2000 ± 0.0010 inch)     |
6.528 ± 0.032 mm (0.2570 ± 0.0013 inch)     |
0.90 ± 0.13 mm (0.035 ± 0.005 inch) by 30 degrees     |
353-5618 120-4337 (1) (2)     |
7.620 ± 0.025 mm (0.3000 ± 0.0010 inch) |
|||
335-8971 (3)     | 212.370 ± 0.013 mm (8.3610 ± 0.0005 inch)     |
6.665 ± 0.032 mm (0.2624 ± 0.0013 inch) |
Show/hide table
( 4 ) | Do not measure this dimension |
( 1 ) | Canceled |
( 2 ) | Non-chamfered insert |
( 3 ) | Oversize |
Caterpillar Information System:
TA19 M4WD Agricultural Transmission Location of Electronic Components for Transmission System
Checking the High-Pressure Relief Valve for Leakage on C6.6 and C4.4 Engines{1288} Checking the High-Pressure Relief Valve for Leakage on C6.6 and C4.4 Engines{1288}
CG137-08 and CG137-12 Industrial Engines Sensor Signal (Analog, Active) - Test
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Assemble
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Disassemble
3516C Generator Set Engines Sensor Signal (PWM) - Test
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Remove and Install
Retrofitting for Ultra Lean Burn (ULB) on a G3512 Engine{1000, 775E} Retrofitting for Ultra Lean Burn (ULB) on a G3512 Engine{1000, 775E}
C3.4B Engines For Caterpillar Built Machines Electronic Control Module
C13, C15, and C18 Tier 4 Final Engines Engine Oil Filter Base
C9.3 Tier 4 Final Engines Engine Oil Filter Base
C4.4 Marine Generator Set Emergency Stopping
3516C Generator Set Engines Sensor Supply - Test
C27 Generator Set Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.3/4.4
C9.3 Engines for Caterpillar Built Machines Water Lines
C13, C15, and C18 Tier 4 Final Engines Water Pump
TA19 M4WD Agricultural Transmission Location of Hydraulic Components for Transmission System
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Regulatory Information (Japan)
C15 Generator Set Refill Capacities
CG137-08 and CG137-12 Industrial Engines Sensor Signal (Analog, Passive) - Test
TA19 M4WD Agricultural Transmission Hydraulic System Schematic
TA19 M4WD Agricultural Transmission Transmission Clutches
C4.4 Engines for Caterpillar Built Machines Inlet Manifold Temperature Sensor
C4.4 Engines for Caterpillar Built Machines Boost Pressure Sensor