Auxiliary Drive (Front) - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
C | 1P-1863 | Retaining Ring Pliers | 1 |
D | 1P-1861 | Retaining Ring Pliers | 1 |
E | 248-3310 | Spanner Wrench | 1 |
F | 1P-0510 | Driver | 1 |
- Use Tooling (F) to install lip seal (14). Lubricate the lip with the lubricant that is being sealed.
Show/hide table
Illustration 2 g02680020 - Install bearing (13). Install lockwasher (12).
- Install locknut (11). Use Tooling (E) to torque the locknut to
108 ± 7 N·m (80 ± 5 lb ft) . If necessary, increase the torque to align the slots.Show/hide tableIllustration 3 g02679882 - Install shaft (9). Use Tooling (D) to install retaining ring (8).
- Lubricate the bore for O-ring seal (10) with the lubricant that is being sealed. Install O-ring seal (10).
Show/hide table
Illustration 4 g02679777 - Install bearing (7) onto gear (5).
- Use Tooling (C) to install retaining ring (6).
Show/hide table
Illustration 5 g02679696 - Install gear (5)
- Install nut (4). Tighten nut (4) to a torque of
290 ± 10 N·m (214 ± 7 lb ft) . Tap the gear down with a hammer and torque nut (4) again to a torque of290 ± 10 N·m (214 ± 7 lb ft) .Show/hide tableIllustration 6 g03676295 - Measure the distance from the end of housing (15) to bearing (7). Dimension (X) is
6.6 ± 0.5 mm (0.26 ± 0.02 inch) .Show/hide tableIllustration 7 g02681817 - Install pulley (3).
- Install studs (2). Tighten studs (2) to a torque of
30 ± 5 N·m (22 ± 4 lb ft) . - Install the washers and install nuts (1). Tighten nuts (1) to a torque of
47 ± 9 N·m (35 ± 7 lb ft) .
Show/hide table
Illustration 1 | g02680056 |
Note: Note the orientation of the lip seal, illustrated above, for installation.
End By:
- Install the auxiliary drive.
Caterpillar Information System:
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Disassemble
3516C Generator Set Engines Sensor Signal (PWM) - Test
C27 and C32 Industrial Engines Auxiliary Drive (Front) - Remove and Install
Retrofitting for Ultra Lean Burn (ULB) on a G3512 Engine{1000, 775E} Retrofitting for Ultra Lean Burn (ULB) on a G3512 Engine{1000, 775E}
C3.4B Engines For Caterpillar Built Machines Electronic Control Module
C13, C15, and C18 Tier 4 Final Engines Engine Oil Filter Base
C9.3 Tier 4 Final Engines Engine Oil Filter Base
C4.4 Marine Generator Set Emergency Stopping
TA19 M4WD Agricultural Transmission Transmission System
TA19 M4WD Agricultural Transmission General Information
Retrofitting a Cat 270 Air Compressor with a BA-921 CR Air Compressor on Certain C13 and C15 On-Highway Engines{1803} Retrofitting a Cat 270 Air Compressor with a BA-921 CR Air Compressor on Certain C13 and C15 On-Highway Engines{1803}
2011/08/04 Correction to Troubleshooting, SENR6493 , "3512 Engine Oil Well Service" {1265, 1901}
CG137-08 and CG137-12 Industrial Engines Sensor Signal (Analog, Active) - Test
Checking the High-Pressure Relief Valve for Leakage on C6.6 and C4.4 Engines{1288} Checking the High-Pressure Relief Valve for Leakage on C6.6 and C4.4 Engines{1288}
TA19 M4WD Agricultural Transmission Location of Electronic Components for Transmission System
2013/08/21 A New Oversized Cylinder Bore Liner Seal Insert Is Available for 3500 Engine Cylinder Block Salvage {1201, 7555}
3516C Generator Set Engines Sensor Supply - Test
C27 Generator Set Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.3/4.4
C9.3 Engines for Caterpillar Built Machines Water Lines
C13, C15, and C18 Tier 4 Final Engines Water Pump
TA19 M4WD Agricultural Transmission Location of Hydraulic Components for Transmission System
303.5E2, 304E2, 305.5E2 and 305E2 Mini Hydraulic Excavators Regulatory Information (Japan)
C15 Generator Set Refill Capacities
CG137-08 and CG137-12 Industrial Engines Sensor Signal (Analog, Passive) - Test