Fuel Injection Timing - Check
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 5P-7306     | 壳体     | 1     |
5P-7305 | 发动机盘车工具     | 1     | |
B     | 435-3146     | 正时销(凸轮轴)     | 1     |
Show/hide table
( 1 ) | 该工具在电动起动马达的孔上使用。 |
Show/hide table
图 1 | g02862116 |
典型示例 |
- 必要时,拆下附件驱动器。 有关正确步骤,请参阅拆解和组装, "附件驱动器 - 拆卸和安装"。 从发动机上拆下螺塞 (1) 。 使用工具 (A) 按正常旋转方向旋转曲轴。
- 将工具 (B) 安装到发动机的孔 (X) 中。 使用工具 (B) ,将凸轮轴定位到正确位置。
注: 安装工具 (B) 时不要使用过大的力量。 在修理过程中不要使用工具 (B) 固定凸轮轴。
- 如果喷油泵的轴不在图 2 中所示的位置,则喷油泵正时可能不正确。 如有必要,拆下喷油泵。 参考拆解和装配以了解正确步骤。
- 确保凸轮轴处于正确的位置。 如有必要,安装喷油泵。 参考拆解和装配以了解正确步骤。 确保喷油泵轴在图 2 中所示的正确位置。 角度 (Y) 应为 45 度。
Show/hide table
图 2 | g02906337 |
典型示例 |
- 如有必要,拆下工具 (B) 。 将塞 (1) 安装到发动机上。
- 如有必要,安装附件驱动器。 有关正确步骤,请参阅拆解和组装, "附件驱动器 - 拆卸和安装"。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Air in Fuel - Test
C3.4B Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C3.4B Engines for Caterpillar Built Machines Valve Guide - Inspect
C9.3 Tier 4 Final Engines Fuel Injector
3516C Generator Sets Burn Prevention
3516C Generator Sets General Hazard Information
TA19 M4WD Agricultural Transmission Transmission
C175-16 Locomotive Engine Turbocharger Inlet Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Fuel Filter Base
2011/08/04 New Valve Train Components for C175 Generator Set Engines {1102, 1121, 1123, 1209}
320E and 323E Excavators Quick Coupler Operation - Circuit for Universal Coupler (If Equipped)
3516C Generator Set Engines Electrical Power Supply - Test
C3.4B Engines for Caterpillar Built Machines Engine Valve Lash - Inspect
C3.4B Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
2011/08/09 New Relay and Relay Socket Are Now Used with EMCP3 Control Panel On Certain 3406C and C18 Generator Sets {4490, 4493}
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Daily Inspection
G3500B Engines Exhaust Bypass Valve - Wastegate
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
2013/08/21 Calculating Cylinder Liner Projection for 3500, 3500B, 3500C, and G3500 Engines {1201, 1216}
Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239} Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239}
3516C Generator Set Engines Emergency Stop - Test
3406C Industrial Engine Safety Messages
3516C Generator Set Engines Prelubrication - Test