Valve Guide - Inspect
进行该项检查是为了确定是否需要更换气门导管。
- 将新气门放入气门导管内。
Show/hide table
图 1 | g00314806 |
测量气门导管中气门的径向移动。 (1) 气门导管 (2) 气门在气门导管中的径向移动 (3) 阀杆 (4) 千分表 (5) 气门头 |
- 将适当的带磁力底座的千分表放在缸盖表面。
- 将门盖边缘提升至 15 mm (0.591 inch )处。
- 径向移动气门,使其远离千分表。 确保气门尽量远离千分表。 将千分表接触点定位到气门头边缘。 将千分表指针位置归零。
- 径向移动气门,使其尽可能靠近千分表。 记录千分表上指示的移动距离。 如果此距离大于气门在气门导管中的最大间隙,则需更换气门导管。 请参考技术规格, "缸盖气门",查看间隙有关信息。
将原始阀导管塞入缸盖中。 当安装新气门导管 (1) 时,必须安装新气门和新气门座镶圈。 缸盖必须再次镗大孔径,以安装新阀导管。 更多信息,请联系您的经销商或代理商。
Caterpillar Information System:
C9.3 Tier 4 Final Engines Fuel Injector
3516C Generator Sets Burn Prevention
3516C Generator Sets General Hazard Information
TA19 M4WD Agricultural Transmission Transmission
C175-16 Locomotive Engine Turbocharger Inlet Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Fuel Filter Base
2011/08/04 New Valve Train Components for C175 Generator Set Engines {1102, 1121, 1123, 1209}
320E and 323E Excavators Quick Coupler Operation - Circuit for Universal Coupler (If Equipped)
3516C Generator Set Engines Electrical Power Supply - Test
370-8083 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100} 370-8083 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100}
2011/07/29 An Improved Procedure Is Now Used to Determine the Reason for a Reoccurring Engine Timing Offset Code on Certain C27 and C32 Engines {1000}
Use of the 352-6061 Liner Seal and the 8N-4707 Filler Band {1201, 1201, 7555} Use of the 352-6061 Liner Seal and the 8N-4707 Filler Band {1201, 1201, 7555}
C3.4B Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C3.4B Engines for Caterpillar Built Machines Air in Fuel - Test
C3.4B Engines for Caterpillar Built Machines Fuel Injection Timing - Check
C3.4B Engines for Caterpillar Built Machines Engine Valve Lash - Inspect
C3.4B Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
2011/08/09 New Relay and Relay Socket Are Now Used with EMCP3 Control Panel On Certain 3406C and C18 Generator Sets {4490, 4493}
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Daily Inspection
G3500B Engines Exhaust Bypass Valve - Wastegate
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
2013/08/21 Calculating Cylinder Liner Projection for 3500, 3500B, 3500C, and G3500 Engines {1201, 1216}
Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239} Correct Combinations of Connecting Rods Allowed in Remanufactured Cylinder Packs for Certain C13 Engines{1218, 1225, 1239}