Fuel Injector
Show/hide table
| |
| Illustration 1 | g02663257 |
| (1) Solenoid assembly | |
Show/hide table
| |
| Illustration 2 | g02663258 |
|
Exhaust side of the cylinder head | |
Show/hide table
| |
| Illustration 3 | g02663259 |
Show/hide table
| |
| Illustration 4 | g02663261 |
|
Intake side of the cylinder head | |
Show/hide table
| Specification for 345-1974 Fuel Injection Pump Gp | |||
| Item | Qty | Part | Specification Description |
| - | - | - | Use the following procedure in order to install the fuel injector group: |
| 1. Lubricate seals (5) with clean engine oil. Lubricate the injector bore (7) with clean engine oil. | |||
| 2. Place the injector into the bore. The pin (4) of the injector fits into the groove (6) of the cylinder head. | |||
| 3. Place the fuel injector clamp (3) with the label "C9" in the UP position. | |||
| 4. When the injector hits the bottom of the bore, torque the bolt (2) to standard torque. | |||
| 5. Lubricate the bore and the nut of the quill assembly with clean engine oil. Also, lubricate the threads in the cylinder head with clean engine oil. | |||
| 6. Insert the quill assembly (8) completely into the cylinder head. Ensure that the ball (9) of the quill assembly is in line with the slot (11) of the cylinder head. | |||
| 10 | 1 | 278-5519 Nut | Torque to |
Caterpillar Information System:
3516C Generator Sets Burn Prevention
3516C Generator Sets General Hazard Information
TA19 M4WD Agricultural Transmission Transmission
C175-16 Locomotive Engine Turbocharger Inlet Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Fuel Filter Base
2011/08/04 New Valve Train Components for C175 Generator Set Engines {1102, 1121, 1123, 1209}
320E and 323E Excavators Quick Coupler Operation - Circuit for Universal Coupler (If Equipped)
3516C Generator Set Engines Electrical Power Supply - Test
370-8083 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100} 370-8083 Plate Assembly - Lifting{0700, 0701, 0703, 1000, 1100}
2011/07/29 An Improved Procedure Is Now Used to Determine the Reason for a Reoccurring Engine Timing Offset Code on Certain C27 and C32 Engines {1000}
Use of the 352-6061 Liner Seal and the 8N-4707 Filler Band {1201, 1201, 7555} Use of the 352-6061 Liner Seal and the 8N-4707 Filler Band {1201, 1201, 7555}
C3.4B Engines For Caterpillar Built Machines Gear Group (Front)
C3.4B Engines for Caterpillar Built Machines Valve Guide - Inspect
C3.4B Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
C3.4B Engines for Caterpillar Built Machines Air in Fuel - Test
C3.4B Engines for Caterpillar Built Machines Fuel Injection Timing - Check
C3.4B Engines for Caterpillar Built Machines Engine Valve Lash - Inspect
C3.4B Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
2011/08/09 New Relay and Relay Socket Are Now Used with EMCP3 Control Panel On Certain 3406C and C18 Generator Sets {4490, 4493}
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Daily Inspection
G3500B Engines Exhaust Bypass Valve - Wastegate
C13, C15, and C18 Tier 4 Final Engines Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
2013/08/21 Calculating Cylinder Liner Projection for 3500, 3500B, 3500C, and G3500 Engines {1201, 1216}