Cylinder Head
Show/hide table
图 1 | g02637022 |
Show/hide table
290-1351 缸盖的技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 2 | 183-8809 气门座圈 | 安装时,收缩气门座圈并将座圈放到缸盖沉孔中。 |
2 | 2 | 289-9745 气门座圈 | 安装时,收缩气门座圈并将座圈放到缸盖沉孔中。 |
3 | 5 | 3B-0623 杯形塞 | 安装前,将 Loctite 11358 涂覆到杯塞的孔中。 |
4 | 5 | 3B-0645 杯塞 | 安装前,将 Loctite 11358 涂覆到杯塞的孔中。 |
D | - | - | 杯塞 (3) 的安装长度为 |
E | - | - | 杯塞 (4) 的安装长度为 |
Show/hide table
图 2 | g02668504 |
Show/hide table
290-1351 缸盖的技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
5 | 1 | 5B-7890 管塞 | 组装前,使用 Loctite C5A 铜防咬合剂润滑螺纹。 |
6 | 6 | 131-0420 缸盖紧固件总成 | 按照下列步骤拧紧缸盖的螺栓:
组装前,将清洁的发动机机油涂抹到螺栓的螺纹上。 将螺栓 1 至螺栓 8 按图 2 中所示的顺序拧紧至扭矩 再将螺栓 1 至螺栓 8 按图 2 中所示的顺序拧紧至扭矩 再将螺栓 1 至螺栓 8 按图 2 中所示的顺序重新拧紧至扭矩 将螺栓 1 至螺栓 8 按顺序转到 180 ± 5 度角,如图 2 所示。 只有在螺栓 1 至螺栓 8 达到最终扭矩后,才拧紧两只螺栓 (8)。 拧紧两只螺栓 (8) 至扭矩为 |
7 | 2 | 131-0421 缸盖紧固件总成 | |
8 | 2 | 5B-0213 螺栓 |
Caterpillar Information System:
3500B and 3500C Marine Engines Valve Mechanism
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing
3500C Marine Engines Camshaft
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing
3516C Generator Set Engines Fuel Injection Pump
3500C Marine Engines Fuel Transfer Pump
Procedures for Using the 232-4686 Cylinder Washer Tank Group European Union Compliant{0374, 0599, 0680, 0738} Procedures for Using the 232-4686 Cylinder Washer Tank Group European Union Compliant{0374, 0599, 0680, 0738}
New Oil and Fuel Filters for C7.1, C6.6, and C4.4 Engines{1261, 1263, 1306, 1308} New Oil and Fuel Filters for C7.1, C6.6, and C4.4 Engines{1261, 1263, 1306, 1308}
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
CG137-08 and CG137-12 Engines Engine Support - Remove and Install
CG137-08 and CG137-12 Industrial Engines Throttle Actuator - Test
C11, C13, and C15 On-highway Engines Engine Oil Level - Check
3516C Generator Set Engines Turbocharger Oil Lines
CG137-08 and CG137-12 Engines Electronic Control Module (Engine) - Remove and Install
3516E Generator Set Engines Exhaust Manifold
G3406 Engine Maintenance Interval Schedule - Standby Generator Set Engines
G3406 Engine Maintenance Interval Schedule - Naturally Aspirated Engines
G3406 Engine Maintenance Interval Schedule - Turbocharged Aftercooled Engines
2011/07/22 Improved Caterpillar Digital Voltage Regulator (CDVR) Is Used for Certain C9, C15, C18, 3300, 3400, G3400, C27, C32, 3500, G3500, and C175 Engines {4467}
G3406 Engine Crankcase Blowby - Test/Record
3500 Engines Air Lines
3500 Engines Air Lines
3500B and 3500C Marine Engines Duplex Engine Oil Filters
349F and 352F Excavators Machine System Specifications Fasteners - Swing Drive and Motor