Camshaft
Show/hide table
图 1 | g02636356 |
Show/hide table
技术规格 - 375-7422 凸轮轴总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 16 | 5P-0076 螺栓 | 拧紧至扭矩为 |
2 | 2 | 128-5993 止推垫圈 | 厚度为 凸轮轴上的止推垫圈槽宽度为 |
A | - | - | 轴承轴颈的直径为 |
Show/hide table
图 2 | g03022617 |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
B | 1 | 4N-1650 定位销 | 定位销从凸轮轴组件末端延伸的长度为 |
C | 1 | 5B-5821 定位销 | 定位销从凸轮轴组件末端延伸的长度为 |
Show/hide table
图 3 | g03022597 |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
- | - | - | 使用以下步骤确定实际凸轮轴凸轮升程:
1. 测量凸轮轴凸尖高度 (E)。 2. 测量基圆 (F)。 3. 从凸轮轴凸尖高度值 (C) 中减去基圆 (D)。 二者之差就是实际凸轮轴凸尖升程 (B)。 |
D | - | - | 规定的凸轮轴凸轮升程: |
进气凸轮为 |
|||
排气凸轮为 |
|||
喷油器凸轮为 |
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing
3516C Generator Set Engines Fuel Injection Pump
3500C Marine Engines Fuel Transfer Pump
Procedures for Using the 232-4686 Cylinder Washer Tank Group European Union Compliant{0374, 0599, 0680, 0738} Procedures for Using the 232-4686 Cylinder Washer Tank Group European Union Compliant{0374, 0599, 0680, 0738}
New Oil and Fuel Filters for C7.1, C6.6, and C4.4 Engines{1261, 1263, 1306, 1308} New Oil and Fuel Filters for C7.1, C6.6, and C4.4 Engines{1261, 1263, 1306, 1308}
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
CG137-08 and CG137-12 Engines Engine Support - Remove and Install
CG137-08 and CG137-12 Industrial Engines Throttle Actuator - Test
C11, C13, and C15 On-highway Engines Engine Oil Level - Check
PM820, PM822, and PM825 Cold Planer Fuel Tank Cap Filter - Replace
12H, 140H, 143H, 160H and 163H Motor Graders Power Train Magnetic Screen (Transmission)
2012/06/08 A New Cylinder Head Gasket and Spacer Plate Are Used for Certain 3500 Locomotive Engines {1100, 1201, 7555}
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing
3500B and 3500C Marine Engines Valve Mechanism
3500C Marine Engines Cylinder Head
3516C Generator Set Engines Turbocharger Oil Lines
CG137-08 and CG137-12 Engines Electronic Control Module (Engine) - Remove and Install
3516E Generator Set Engines Exhaust Manifold
G3406 Engine Maintenance Interval Schedule - Standby Generator Set Engines
G3406 Engine Maintenance Interval Schedule - Naturally Aspirated Engines
G3406 Engine Maintenance Interval Schedule - Turbocharged Aftercooled Engines
2011/07/22 Improved Caterpillar Digital Voltage Regulator (CDVR) Is Used for Certain C9, C15, C18, 3300, 3400, G3400, C27, C32, 3500, G3500, and C175 Engines {4467}
G3406 Engine Crankcase Blowby - Test/Record
3500 Engines Air Lines