Air Shutoff - Remove and Install
- Pull the emergency knob on the air shutoff or press the emergency stop button in order to release the blade latch on the air shutoff.
Show/hide table
Illustration 1 g02476926 - Disconnect hose assembly (1) from air shutoff (3).
- Loosen band clamps (2) and clamp (4). Remove air shutoff (3).
- If necessary, remove hose assembly (1). Disconnect hose assemblies (5) and harness assembly (6) from control valve assembly (7).
- Remove the bolts and control valve assembly (7).
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
 |
|
Personal injury or death can occur from not following the proper procedure or the recommended tooling. To prevent the possibility of injury or death, follow the established procedure using the recommended tooling. |
Show/hide table
|
|
Before you remove the air intake shutoff, pull the trip knob on the air intake shutoff or press the emergency stop button in order to release the blade latch. If the blade latch is released after the air intake shutoff is removed, serious personal injury can result. |
- Clean all mating surfaces. Position control valve assembly (7) and install the bolts.
- If necessary, connect harness assembly (6) and hose assemblies (5) to control valve assembly (7). Install hose assembly (1).
- Place air shutoff (3) in position. Install band clamps (2) and clamp (4). Tighten clamp (4) to a torque of
8.5 ± 2.0 N·m (75 ± 18 lb in) . - Connect hose assembly (1) to air shutoff (3).
- Reset the air shutoff to the "OPEN" position.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| |
| Illustration 2 | g02476926 |
Caterpillar Information System:
G3304B and G3306B Engines Engine Performance - Test
C15 Petroleum Engines Electrical Power Supply - Test
G3304B and G3306B Engines Starting with Jump Start Cables
G3304B and G3306B Engines Before Starting Engine
G3516 Petroleum Engine Control Panel - Inspect/Test
C15 and C18 Petroleum Generator Sets Refill Capacities
XQ60 Rental Generator Set Sensors and Electrical Components
C3.4B Industrial Engine Sensors and Electrical Components - Aftertreatment
C15 Petroleum Engines Electronic Control Module - Remove and Install
G3500J Engines Refill Capacities
3116 and 3126 Marine Engines Coolant - Change
C4.4 Industrial Engine Exhaust Elbow - Remove and Install - Top Mounted and Side Mounted Turbocharger Exhaust Elbow
G3500 Engines Coolant Level - Check
G3500 Engines Coolant (DEAC) - Change
300.9D and 300.9D VPS Mini Hydraulic Excavator Engine Valve Lash - Check/Adjust
C4.4 Industrial Engine Turbocharger - Install - Top Mounted Turbocharger
C4.4 Industrial Engine Turbocharger - Remove - Top Mounted Turbocharger
C4.4 Industrial Engine Turbocharger - Remove - Side Mounted Turbochargers
C4.4 Industrial Engine Turbocharger - Install - Side Mounted Turbochargers
2011/04/04 An Updated Procedure for Manual Engine Shutdown in the Engine Operation and Maintenance Manual (OMM) Is Available {1000}
C15 and C18 Petroleum Generator Sets Control Panel - Inspect/Test
C15 and C18 Petroleum Generator Sets Coolant (DEAC) - Change
C15 and C18 Petroleum Generator Sets Coolant Level - Check
G3304B and G3306B Engines Control Panel - Inspect/Test