Crankshaft Position Sensor - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 断开线束组件 (2) 。
Show/hide table
图 1 | g02229293 |
- 拆下螺栓 (1) 和曲轴位置传感器 (3) 。
- 从曲轴位置传感器 (3) 上拆下 O 形密封圈。
安装步骤
- 按与拆卸相反的顺序安装曲轴位置传感器 (3) 。
- 将新的 O 形密封圈安装到曲轴位置传感器 (3) 上。 用清洁的发动机机油润滑 O 形密封圈。
- 将曲轴位置传感器 (3) 安装在前壳体中。 安装螺栓 (3) 。 将螺栓 (3) 拧紧至扭矩为 28 ± 7 N·m (21 ± 5 lb ft)。
Caterpillar Information System:
C9.3 Tier 4 Interim Engines Diesel Particulate Filter Temperature Is High
2010/08/23 Use Proper Procedures with Speed/Timing Sensor Diagnostic Codes for C175 Generator Set Engines {1408, 1439, 1912}
3512C HD Locomotive Engine Cooling System Coolant (DEAC) - Change
3512C HD Locomotive Engine Belts - Inspect/Adjust/Replace
C27 Generator Set Overhaul Considerations
2010/09/17 New Silicone Power Cables Are Now Used For Power Connections On Certain Cat Generator Sets {1408, 4460}
3512C HD Locomotive Engine Engine Oil Level - Check
3512C HD Locomotive Engine After Stopping Engine
2010/08/23 New Locknuts for the Exhaust Manifold Are Available for Certain Commercial Engines {1059}
2010/08/23 New Locknuts for the Exhaust Manifold Are Available for Certain Truck Engines {1059}
C27 and C32 Industrial Engines Camshaft Position Sensor - Remove and Install
2010/08/26 An Improved Locknut Is Now Used to Tighten the Exhaust Manifolds onto the Cylinder Heads of Certain Engines {1059, 7553}
G3304B and G3306B Engines Cover Group (Front Housing)
2012/06/29 A New Engine Oil Filter Element Is Used for Certain C175-16 Engines {1306, 1308}
120 and 120 AWD Motor Grader Scarifier Digging Angle - If Equipped
C27 and C32 Industrial Engines Coolant Temperature Sensor - Remove and Install
120 and 120 AWD Motor Grader Axle Oscillation Bearings - Lubricate
120 and 120 AWD Motor Grader Drawbar Ball and Socket - Lubricate
3512C Oil Well Service Engines Safety Messages
2011/01/10 A New Wiring Harness Kit Is Available in Order to Make Repairs on Certain Truck Engines {1254, 1290, 1408}
2010/12/06 A New Injector Wiring Harness Kit Is Available to Make Repairs on Certain Commercial Engines {1254, 1290, 1408}
120 and 120 AWD Motor Grader Drawbar Ball and Socket End Play - Check/Adjust
3512C Oil Well Service Engines Product Lifting
3516C Locomotive Engines Selective Catalytic Reduction Module - Disassemble