Gear Group (Front) - Install
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清除前板与缸体之间接触面上的旧密封垫。 将新密封垫安装在缸体上。 按照缸体底面的轮廓切割密封垫。
- 安装密封垫、前板 (4) 和螺栓 (3) 。
Show/hide table
图 1 | g01952881 |
Show/hide table
注意 |
---|
将正时齿轮板在缸体上固定到位的螺栓的螺栓头的厚度应减小。 齿轮间隙需要减小的螺栓头厚度。 |
- 如有必要,将正时轮和螺栓安装到凸轮轴轴承 (1) 上。 将惰齿轮 (5) 上的标记 (B) 与曲轴齿轮上的标记 (B) 对齐。 将凸轮轴齿轮上的标记 (C) 与曲轴齿轮上的标记 (C) 对齐。 安装凸轮轴齿轮 (1) 和螺栓 (2) 。 拧紧螺栓 (2) 至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
Show/hide table
图 2 | g01953041 |
End By: 安装前壳体。
Caterpillar Information System:
797F and 797F XQ Off-Highway Truck Power Train Planetary Case and Parts Group - Front Module
C7.1 Industrial Engine and Generator Set Mode Switch Setup
G3304B and G3306B Engines Gear Group (Front) - Remove
14L Motor Grader Water Pump - Remove and Install
C9.3 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
Damaged Liner Seals on 3400 Reman Cylinder Packs {1201, 1216, 1239} Damaged Liner Seals on 3400 Reman Cylinder Packs {1201, 1216, 1239}
G3304B and G3306B Engines Housing (Front) - Install
G3304B and G3306B Engines Housing (Front) - Remove
C7.1 Industrial Engine and Generator Set Multiposition Switch Setup
797F and 797F XQ Off-Highway Truck Steering System Bypass Switch (Hydraulic Fan, Steering Oil Filter)
797F and 797F XQ Off-Highway Truck Braking System Gear Motor (Rear Axle Lubrication)
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism
C9.3 Engines for Caterpillar Built Machines Soot Antenna - Remove and Install
G3304B and G3306B Engines Valve Mechanism Cover - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Remove and Install
793F AC Off-Highway Truck Hydraulic and Braking System Relief Valve (Main)
793F AC Off-Highway Truck Hydraulic and Braking System Solenoid Valve (Brake Pump Unloader)
797F and 797F XQ Off-Highway Truck Braking System Slack Adjuster (Front Brakes)
Calculations for Required Inlet Pressure and Back Pressure of the Fuel on C175 Engines that are Utilizing a Day Tank or Standby Application{1250} Calculations for Required Inlet Pressure and Back Pressure of the Fuel on C175 Engines that are Utilizing a Day Tank or Standby Application{1250}
2010/01/18 New O-Ring Seals Are Used on the Front Housings of 3500 Engines {1151, 1162, 1166, 1206, 1207}
G3304B and G3306B Engines Rocker Shaft and Push Rod - Remove
793F and 793F CMD Off-Highway Truck Braking System Slack Adjuster (Rear Brakes)
G3304B and G3306B Engines Rocker Shaft and Push Rod - Install
793F AC Off-Highway Truck Hydraulic and Braking System Check Valve (Service Brake Accumulator)