Valve Mechanism Cover - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 彻底清洁气门机构盖周围的区域以防止异物进入气缸和气门机构。 拆下气门机构盖之后,将一个清洁的盖子放在开口上,以防止悬浮尘埃和磨损颗粒进入。
- 拆下螺栓 (2) 将呼吸器组件 (1) 固定在位的垫圈。
Show/hide table
图 1 | g01953184 |
- 将呼吸器组件 (1) 、烟气排放软管和 O 形密封圈作为一个整体拆下。
- 拆下螺栓 (4) 和锁紧垫圈。 拆下气门机构盖 (3) 和整体式密封。
注: 拆卸气门机构盖之前,确保所有线束组件都已断开。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 5H-2471     | 粘接剂     | -     |
- 将工具 (A) 涂覆在气门机构盖 (3) 的表面上。 安装整体式密封、气门机构盖 (3) 、锁紧垫圈和螺栓 (4) 。
Show/hide table
图 2 | g01953184 |
Show/hide table
图 3 | g01953198 |
G3304B |
Show/hide table
图 4 | g01953199 |
G3306B |
- 按数字顺序拧紧 G3304B 发动机的螺栓至扭矩为 11 ± 3 N·m (95 ± 27 lb in)。 按数字顺序拧紧 G3306B 发动机的螺栓至扭矩为 16 ± 3 N·m (140 ± 27 lb in)。
注: 确保所有线束组件都已连接。
- 安装 O 形密封圈、烟气排放软管和呼吸器组件 (1) 。 安装垫圈和螺栓 (2) 。 拧紧螺栓 (2) 至扭矩为 14 ± 3 N·m (125 ± 27 lb in)。
Caterpillar Information System:
C9.3 Engines for Caterpillar Built Machines Soot Antenna - Remove and Install
G3304B and G3306B Engines Gear Group (Front) - Install
797F and 797F XQ Off-Highway Truck Power Train Planetary Case and Parts Group - Front Module
C7.1 Industrial Engine and Generator Set Mode Switch Setup
G3304B and G3306B Engines Gear Group (Front) - Remove
14L Motor Grader Water Pump - Remove and Install
C9.3 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
Damaged Liner Seals on 3400 Reman Cylinder Packs {1201, 1216, 1239} Damaged Liner Seals on 3400 Reman Cylinder Packs {1201, 1216, 1239}
G3304B and G3306B Engines Housing (Front) - Install
G3304B and G3306B Engines Housing (Front) - Remove
C7.1 Industrial Engine and Generator Set Multiposition Switch Setup
797F and 797F XQ Off-Highway Truck Steering System Bypass Switch (Hydraulic Fan, Steering Oil Filter)
C15 and C18 Engines for Caterpillar Built Machines Flywheel - Remove and Install
793F AC Off-Highway Truck Hydraulic and Braking System Relief Valve (Main)
793F AC Off-Highway Truck Hydraulic and Braking System Solenoid Valve (Brake Pump Unloader)
797F and 797F XQ Off-Highway Truck Braking System Slack Adjuster (Front Brakes)
Calculations for Required Inlet Pressure and Back Pressure of the Fuel on C175 Engines that are Utilizing a Day Tank or Standby Application{1250} Calculations for Required Inlet Pressure and Back Pressure of the Fuel on C175 Engines that are Utilizing a Day Tank or Standby Application{1250}
2010/01/18 New O-Ring Seals Are Used on the Front Housings of 3500 Engines {1151, 1162, 1166, 1206, 1207}
G3304B and G3306B Engines Rocker Shaft and Push Rod - Remove
793F and 793F CMD Off-Highway Truck Braking System Slack Adjuster (Rear Brakes)
G3304B and G3306B Engines Rocker Shaft and Push Rod - Install
793F AC Off-Highway Truck Hydraulic and Braking System Check Valve (Service Brake Accumulator)
793F AC Off-Highway Truck Hydraulic and Braking System Check Valve (Parking Brake Accumulator)
C13, C15, and C18 Tier 4 Interim Engines ARD Temperature Is Low