Catalyst - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 352-5891     | 吊带     | 2     |
B     |     | Loctite 771     | -     |
- 断开电缆组件 (2) 后拆下烟尘天线 (1) 。
Show/hide table
高温发动机部件可能导致灼伤。 进行发动机保养之前让发动机和部件冷却下来。 |
Show/hide table
在处理用过的柴油微粒滤清器或催化转化器消声器时,请配戴护目镜、手套、防护服以及经过职业安全与健康管理局(NIOSH)批准的 P95 或 N95 半面式防尘面罩。 否则可能造成人身伤害。 |
Show/hide table
图 1 | g02198653 |
注: 确保烟尘天线和线束组件接头清洁无异物。 为了防止异物进入接头,断开后务必利用塞子或保护盖封堵接头。
- 松开卡箍组件 (4) 后将卡箍组件滑离催化剂 (7) 。
Show/hide table
图 2 | g02199118 |
- 断开温度传感器 (5) 和压力传感器 (6) 。
- 将工具 (A) 套到催化剂 (7) 上。 断开卡箍组件 (8) 和 (3) 后拆下催化剂。 催化剂的重量约为 21 kg (46 lb)。
- 丢弃卡箍组件 (4) 。
安装步骤
- 按相反顺序安装柴油氧化催化剂 (7) 。
- 安装新卡箍组件 (4) 。 将工具 (B) 涂抹到卡箍组件 (4) 的螺纹上。 将卡箍组件 (4) 上紧到 50 ± 1 N·m (37 ± 1 lb ft) 的扭矩。 不要使用电动工具上紧卡箍组件 (4) 。
- 确认球窝接头 (G) 的杯不接触球头 (F) 的半径。 定位球形卡箍 (8) 后用手上紧球形卡箍 (8) 。 球形卡箍 (8) 应当位于接头的中心位置。 尺寸 (C) 和尺寸 (D) 间的差值应当在 2 mm (0.08 in) 的范围内。 沿球形卡箍 (8) 四周以 90° 的间隔重复测量。 必要时,调整球形卡箍 (8) 。 不要使用电动工具上紧卡箍组件 (8) 。 将球形卡箍 (8) 上紧到 35 ± 2 N·m (26 ± 1 lb ft) 的扭矩。
Show/hide table图 3 g02199213
卡箍组件 (8) 的底视图。
Show/hide table图 4 g02199293
组件上卡箍组件 (8) 的剖面图。
- 将工具 (B) 涂抹到卡箍组件 (3) 距离 (X) 的螺纹上。 距离 (X) 高出耳轴 25 mm (1 in)。 利用手动工具上紧卡箍组件 (3) 。 把卡箍组件 (3) 拧紧至扭矩为 16.5 ± 1.5 N·m (146 ± 13 lb in)。
Show/hide table图 5 g02199513
- 将工具 (B) 涂抹到温度传感器 (5) 和烟尘传感器 (1) 的螺纹上。 将温度传感器 (5) 和烟尘传感器 (1) 上紧到 45 ± 5 N·m (33 ± 4 lb ft) 的扭矩。 当连接到烟尘天线 (1) 时,用手带紧电缆组件 (2) 。
注: 确保烟尘天线和电缆组件接头清洁无异物。
Caterpillar Information System:
C7.1 Industrial Engine and Generator Set Electrical Connectors - Inspect
C13 Engine Electronic Unit Injector Sleeve - Install
C13 Engine Electronic Unit Injector Sleeve - Remove
C13 Engine Electronic Unit Injector - Install
C13 Engine Electronic Unit Injector - Remove
C13 Engine Fuel Transfer Pump - Install
C13 Engine Fuel Transfer Pump - Remove
C13, C15, and C18 Tier 4 Interim Engines ARD Nozzle - Test
C7.1 Industrial Engine Engine Crankcase Breather Element - Replace
C13 Engines for Caterpillar Built Machines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor
C13 Engines for Caterpillar Built Machines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install
C13 Engines for Caterpillar Built Machines Temperature Sensor (Aftercooler Air) - Remove and Install
C9 Marine Auxiliary and Generator Set Engines Fumes Disposal Filter Element - Replace - Heavy Duty Closed Crankcase Ventilation Fumes Disposal Filter (If Equipped)
An Improved Filter Element for the Power Train has Been Released{3067, 5068} An Improved Filter Element for the Power Train has Been Released{3067, 5068}
C9 On-highway Engine Diesel Particulate Filter
G3516 Power Module Crankcase Pressure - Measure - Engines with Fumes Disposal Filters
Cat Commercial Diesel Engine Fluids Recommendations Biodiesel
2009/04/20 A New Connector Assembly and Hose Assembly are Now Used on Certain Caterpillar Products {5079, 5117}
PM3516 Power Modules Fumes Disposal Filter Element - Replace
C9 On-highway Engine Diesel Particulate Filter Temperature and Pressure Sensor
C13 Engine Inlet and Exhaust Valve Springs - Remove and Install
C13 Engine Inlet and Exhaust Valves - Remove and Install
C13 Engine Inlet and Exhaust Valve Guides - Remove and Install
C13 Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install