Main Control Valve - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 液压系统被异物污染会缩短液压系统部件的使用寿命。 为了避免污染物进入液压系统,总要在断开后塞住或盖住管路、管接头或软管。 罩住已解体的部件,然后在组装前正确清洁它们。 在更换任何主部件后,或特别是在部件故障后,正确清洁液压系统,以便去除全部污染物。 |
- 将工具 (A) 和适当的起吊设备连接到主控制阀 (42) 。 主控制阀 (42) 的重量约为 499 kg (1100 lb)。 定位主控制泵 (42) 并安装螺栓 (43) 。 安装软管组件 (41) 。
Show/hide table
图 1 | g01212110 |
- 安装阀总成 (39) 、接头组件 (40) 和接头 (38) 。
Show/hide table
图 2 | g01211999 |
- 连接管组件 (35) 。 连接弯头组件 (36) 。 连接软管组件 (34) 。 连接软管组件 (33) 。 连接软管组件 (37) 。
Show/hide table
图 3 | g01211997 |
- 连接管组件 (28) 和 (29) 。 连接软管组件 (30) 、 (31) 和 (32) 。
Show/hide table
图 4 | g01211996 |
- 连接管组件 (24) 和 (25) 。 连接软管组件 (23) 和 (26) 。 安装软管组件 (22) 和 (27) 。
Show/hide table
图 5 | g01211995 |
- 安装螺栓 (21) 。
Show/hide table
图 6 | g01211994 |
- 安装 3 个接头 (20) 。 连接 3 个软管组件 (19) 。
Show/hide table
图 7 | g01211993 |
- 将支承组件 (12) 和软管组件 (16) 定位在主控制阀上,并安装挡块 (15) 。 连接支承组件 (12) 。
Show/hide table
图 8 | g01211878 |
- 连接软管组件 (13) 、 (14) 、 (16) 和 (18) 。 连接软管组件 (11) 。 连接线束组件 (17) 。
- 连接软管组件 (9) 和 (10) 。 连接 3 个软管组件 (8) 。
Show/hide table
图 9 | g01211838 |
- 连接 12 个软管组件 (6) 和软管组件 (7) 。
Show/hide table
图 10 | g01211837 |
- 定位薄板组件 (5) 后安装螺栓 (4) 。
Show/hide table
图 11 | g01211836 |
- 连接 14 个软管组件 (3) 。
Show/hide table
图 12 | g01211834 |
- 由两个人一起将薄板组件 (2) 放置到位。 薄板组件 (2) 的重量约为 25 kg (55 lb)。 安装螺栓 (1) 。
Show/hide table
图 13 | g01209651 |
- 向液压油箱注油。 请参阅操作和保养手册, "液压系统机油 – 更换"。
Caterpillar Information System:
C6.6 Marine Generator Set Cooling System - Inspect
G3500B Engines Ignition Secondary - Test
C6.6 Marine Generator Set Alternator - Test
2008/12/29 A New Coolant Hose Is Used {1380, 1383}
C6.6 Marine Generator Set Glow Plugs - Test
G3500B Engines Ignition Primary - Test
2008/12/22 New PL1000E Software is Now Available {7610}
Compatible Puller Stud and Hydraulic Cylinder Capacity Chart {0599, 7000, 7562} Compatible Puller Stud and Hydraulic Cylinder Capacity Chart {0599, 7000, 7562}
793F and 797F Off-Highway Trucks Chassis Electronic Control System MID 087 - CID 2851 - FMI 06
793F and 797F Off-Highway Trucks Chassis Electronic Control System MID 087 - CID 2851 - FMI 05
793F and 797F Off-Highway Trucks Chassis Electronic Control System MID 087 - CID 2851 - FMI 03
Nozzle Heater Assembly Does Not Seat Properly{108B, 108E, 108M} Nozzle Heater Assembly Does Not Seat Properly{108B, 108E, 108M}
G3500B Engines Indicator Lamp - Test
G3500B Engines Sensor Signal (Analog, Active) - Test
G3516 Petroleum Engines Electric Starting Motor - Remove and Install
G3516 Petroleum Engines Air Starting Motor - Disassemble
G3516 Petroleum Engines Air Starting Motor - Assemble
2009/02/01 A New Turbocharger Oil Line Is Used on C15 Truck Engines {1052, 1307}
2011/05/04 A New Coil Assembly is Now Used {5479}
793F Off-Highway Truck Braking
CX31-P600 Petroleum Transmission Relief Valve (Transmission Oil Filter Bypass)
CX31-P600 Petroleum Transmission Pressure Switch (Transmission Oil Filter Bypass)
Cat Commercial Diesel Engine Fluids Recommendations Lubricant Information
C6.6 Marine Generator Set CID 0268 FMI 02