Cylinder Head Valves
Show/hide table
Illustration 1 | g00903737 |
(1) Valve spring
- Standard free length for C1.5 and C2.2 ... 35.0 mm (1.378 inch)
- Service limit for the standard free length for C1.5 and C2.2 ... 33.5 mm (1.319 inch)
- Standard test force for C1.5 and C2.2 ... 79 N (17.8 lb)
- Service limit for the standard test force for C1.5 and C2.2 ... 68.6 N (15.4 lb)
- Length under test force for C1.5 and C2.2 ... 30.4 mm (1.197 inch)
(2) Valve guide seal for the exhaust valve
- Identification ... Black garter spring
- Label on the black garter spring ... "EX"
(3) Valve guide seal for the inlet valve
- Identification ... Silver garter spring
(4) Valve spring recess for the valve spring
Show/hide table
Illustration 2 | g00903744 |
(5) Exhaust valve guide
(A) Clearance between the exhaust valve and the valve guide
- C1.5 and C2.2 ... 0.050 to 0.075 mm (0.0020 to 0.0030 inch)
- Service limit ... 0.25 mm (0.010 inch)
(6) Inlet valve guide
(A) Clearance between the inlet valve and the valve guide
- C1.5 and C2.2 ... 0.030 to 0.060 mm (0.0012 to 0.0024 inch)
- Service limit ... 0.2 mm (0.008 inch)
(7) Exhaust valve stem
- Diameter of the exhaust valve stem for C1.5 and C2.2 ... 6.940 to 6.955 mm (0.2732 to 0.2738 inch)
- Service limit ... 6.84 mm (0.269 inch)
(8) Inlet valve stem
- Diameter of the inlet valve stem for C1.5 and C2.2 ... 6.955 to 6.970 mm (0.27382 to 0.27441 inch)
- Service limit ... 6.89 mm (0.271 inch)
Show/hide table
Illustration 3 | g00845823 |
(B) Thickness of the valve head ... 0.925 to 1.075 mm (0.03642 to 0.04232 inch)
Service limit ... 0.5 mm (0.020 inch)
Show/hide table
Illustration 4 | g00903773 |
(C) Valve depth below the cylinder head face
-
Inlet and exhaust valves
- C1.5 ... 0.65 to 0.95 mm (0.0256 to 0.0374 inch)
-
Inlet and exhaust valves
- C2.2 ... 0.65 to 0.95 mm (0.0256 to 0.0374 inch)
- Service limit ... 1.8 mm (0.071 inch)
Show/hide table
Illustration 5 | g00903760 |
(D) Valve seat angle ... 45 degrees
(E) Contact face
-
Exhaust valve
- C1.5 ... 1.66 to 1.73 mm (0.0653 to 0.0681 inch)
- C2.2 ... 1.94 to 2.16 mm (0.0764 to 0.0850 inch)
- Service limit ... 2.5 mm (0.098 inch)
-
Inlet valve
- C1.5 ... 1.66 to 1.87 mm (0.0653 to 0.0736 inch)
- C2.2 ... 1.50 to 2.00 mm (0.0591 to 0.0790 inch)
- Service limit ... 2.5 mm (0.098 inch)
Caterpillar Information System:
C1.5 and C2.2 Generator Sets Valve Mechanism Cover
C1.5 and C2.2 Generator Sets Rocker Shaft
C1.5 and C2.2 Generator Sets Lifter Group
C1.5 and C2.2 Generator Sets Fuel Injection Nozzles
C1.5 and C2.2 Generator Sets Fuel Injection Pump
C1.5 and C2.2 Generator Sets Fuel Injection Lines
C1.5 and C2.2 Generator Sets Engine Design
C15 and C18 Petroleum Generator Sets Generator Bearing - Lubricate
795F AC and 795F AC XQ Off-Highway Trucks Engine Valve Lash - Check/Adjust
C6.6 Marine Generator Set Belts - Inspect/Adjust/Replace - Single Belt
C6.6 Marine Generator Set Belts - Inspect/Adjust/Replace - Two Belt Set
C6.6 Marine Generator Set Maintenance Interval Schedule
C1.5 and C2.2 Generator Sets Cylinder Head
C1.5 and C2.2 Generator Sets Exhaust Manifold
C1.5 and C2.2 Generator Sets Camshaft
C1.5 and C2.2 Generator Sets Engine Oil Relief Valve
C1.5 and C2.2 Generator Sets Water Temperature Regulator
C1.5 and C2.2 Generator Sets Cylinder Block
C1.5 and C2.2 Generator Sets Crankshaft
C1.5 and C2.2 Generator Sets Connecting Rod Bearing Journal
C1.5 and C2.2 Generator Sets Main Bearing Journal
C1.5 and C2.2 Generator Sets Connecting Rod
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Cylinder Head
C1.5 and C2.2 Generator Sets Glow Plugs