Crankcase Breather - Remove and Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
Illustration 1 | g01457279 |
- Remove bolt (2) and the washer from breather assembly (3).
- Loosen hose clamp (1) and hose clamp (7). Remove clip (5) and hose (4).
- Remove breather assembly (3) and the O-ring seal.
- Remove hose clamp (6), the hose assembly for the oil drain, the bolts, and fumes disposal group (8), if necessary.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install fumes disposal group (8), the bolts, the hose assembly for the oil drain, and hose clamp (6), if necessary.
- Check the condition of the O-ring seal. Replace the O-ring seal if the O-ring seal is damaged.
- Install the O-ring seal and breather assembly (3).
- Install bolt (2) and the washer. Tighten bolt (2) to a torque of
7 ± 3 N·m (60 ± 27 lb in) . - Install hose (4) and clip (5). Tighten hose clamp (7) and hose clamp (1).
Show/hide table
Illustration 2 | g01457279 |
Caterpillar Information System:
345D, 349D and 349D2 Excavators Hydraulic System Negative Flow Control System
793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Pressure Switch (Hydraulic Fan, Steering Oil Filter)
345D, 349D and 349D2 Excavators Hydraulic System Main Control Valve
G3520B Industrial Engines Engine Control Panel
C7 PETROLEUM Petroleum Engine Exhaust Manifold - Remove and Install
793F and 793F CMD Off-Highway Truck Braking System Pump Drive Shaft
G3520B Industrial Engines Air/Fuel Ratio Control - Adjust - NO<SUB>X</SUB> Feedback
C7 PETROLEUM Petroleum Engine Turbocharger - Install
Failure of Reused Rotocoils in 3500 Engines{1100} Failure of Reused Rotocoils in 3500 Engines{1100}
345D, 349D and 349D2 Excavators Hydraulic System Main Hydraulic Pump
345D, 349D and 349D2 Excavators Hydraulic System Hydraulic Filter (Pilot)
345D, 349D and 349D2 Excavators Hydraulic System Gear Pump (Pilot)
307E2 Mini Hydraulic Excavator Machine System Specifications Bucket Linkage
2008/03/17 Improved Fastening for the Turbocharger to the Exhaust Manifold {1052, 1053}
345D Excavator and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Relief Valve (Main) - Heavy Lift
C11 and C13 Engines Turbocharger
C11 and C13 Engines Turbocharger
3512C and 3516C Industrial Engines Turbocharger
C18 Marine Engines Configuration Parameters
345D, 349D and 349D2 Excavators Hydraulic System Boom Hydraulic System
G3520B Industrial Engines General Information (Electronic Control System)
Salvage of Center Bearing in Torque Converter Input Housing {3101, 3127} Salvage of Center Bearing in Torque Converter Input Housing {3101, 3127}
G3520B Industrial Engines Ignition Transformer
G3520B Engines Gear Group (Front)